Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
where could i find detailed current consumption and timings (wake-up, rx, tx, power down) in connected mode for RF51822, in order to compute average current value for...
My device :
nRF6310 Rev 1.4(nRF6700)
nRF2722 Rev 2.2
I will use those devices to test RF communication between nRF2722 and nRF51822. Software environment is...
Hello,
I am playing with the s110 ble_app_proximity example.
As I do not want to store info in flash, I do not want to use the bond manager, that stores data in flash...
I'm currently using a combination of the GNU ARM Eclipse plugin and the unofficial pure-gcc Makefiles to build my nRF51822 code. The build works fine with the pure-gcc Makefiles...
Hello everyone,
I want to create a real-time wireless sensor network. There are 8 sensors in the net. I use two nRF24LE1 as receivers to recieve the datas stimultaneously...
Any idea what the max SPI slave clock frequency is on the nRF51822? The product specification (page 46, v2.0) says the max SCK frequency is 2MHz, but I was wondering if any...
Hello together,
I am searching for the source code of the MasterControl Panel for Android.
Is there a reason, that the code is not available, because the source code of...
Hello,
I'd like to know, if there is any difference between nRF51822 EK and DK, except device number. Two devices from EK will be enough for me.
www.nordicsemi.com/....
Hi,
We are interested in integrating BT MP3 player in our product and Im wondering if we can use Nordic SoC to stream audio via bluetooth to the Headset? So create an A2DP...
Hello, I am trying to develop a low power application by using nrf51822 EK board.
In " Reference manual v2.0, 11.1.3 System ON mode ",
it says there is a mechanisms can...
I am using app_gpiote_user_register() and ads_interrupt_enable() to define a ping change interrupt. When the code runs, I can see on my logic analyzer that the GPIO pin assigned...
I have a nrf51822 project with S110 (v6.0.0) softdevice. I am using latest sdk (v5.1.0). I compile the project successfully with gcc and it does run too. But I struggle with...
I'm trying to reconcile two things I read about the softdevice. The GAP roles that are supported include broadcaster and peripheral. Also, there is support for a GATT client...
Hello
I am trying to build the nAN-36 application.
The main.c file include at least two files that I do not find:
#include "ble_eval_board_pins.h"
#include "ble_stack_handler...
We're trying to implement initial programming of the chip using SWD. We can connect to the chip and successfully enter debug mode but from that point on (as per section 11...
