I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
Hi,
I am using the nrf8001 module provided by adafruit ( www.adafruit.com/.../1697) but it's not clear if the RDY and REQ pins available on the chip are active low or not...
I have made a small device composed by
SD310-1.0, boootloader and application. The device is sealed to be waterproofed and has a serial conenction used by the custom bootloader...
I've been working with SDK 7.1 and I am struggling to understand how to get the makefile working with an NRF51822-QFAA device rather than a nRF51422-QFAC. I have samples of...
Hi all,
I did this upgrade hoping to have a TX_COMPLETE event issue fixed (I'm not able to send more than 1 buffer per connection it seems in my notification based service...
Hi,
There are two advertise nodes, only broadcast (one packet/s) . The S120 star scan. At the beginning everything is OK，but after a while, maybe 3-5 minutes, only one...
Dear all,
I've loaded this example github.com/.../Blinky_ble
into the nrf6310 as it is, and s110_nrf51822_7.0.0 as a softdevice
I am connecting to the module through...
I need the nRF51-DK-HW hardware files ，but without a product key.
And I cann't buy a nRF51 in CHINA.
Someone can give me a product key or
help me to buy a nRF51.
Thanks...
Hello everyone,
I have developed a firmware that makes accurate time of flight measurements, working with my own protocol.
Now I need to integrate this firmware with BLE...
Hi,
We would like to switch to a stand alone debugger for nRF51822, However in the product specs ( www.nordicsemi.com/.../nRF51822 ) mentioning that standalone programmer...
Hi guys,
I have nRF51822 Evaluation Kit.
I am trying to make simple project for my senior design.
Here is the setup.
I need to control simple on/off switch from...
Hi, I'm developing a BLE application.
I want to send multiple packets (from same characteristic) per connection interval.
I've read this question:
devzone.nordicsemi...
hello,
I am trying to develop an application using s130 softdevice on NRF51822 board.
i am able to do a undirected adverisement after a scanning. But when i am trying...
Hi
I use proprietary service to transmit data between iOS and nRF51822. The example I referred to is below.
C:\Keil\ARM\Device\Nordic\nrf51822_v6.0.0.43681_Backup\Board...
Hello,
I need to send packets on a specified advertising channel and receive them at the same advertising channel. Unfortunately, the SoftDevice API does not seem to support...
Hi,
I have several nRF51822 which are far away from each other and I want to communicate with all of them without need to go to deferent places to get the signal.
Does...
