Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All,
I am new to the field and working on nRF51822. As mentioned in the question, which is the easiest way to Implement a simple LED blink (10Hz) for 5 seconds?. Is...
I have successfully tested the SPI master loopback example on pca10001 eval board. I have a few questions regarding a real-world scenario when there is a slave SPI present...
I'm trying to follow the instructions for "nRF51822 Beacon Firmware Documentation" for over the air firmware upgrade of the smart beacon, but I can't find the soft device...
Could this be my problem?
devzone.nordicsemi.com/.../s110-7-0-0-can-i-write-my-own-mbr
an application now starts at 0x15000 which is to make room for an extra 4Kbytes...
Hi,
I am new to BLE Development. Currently I am using NORDIC Development board (SDK Ver 5.2 &Soft device S110). I want to write a small program to establish the connection...
I'm trying to get a handle on the various ways I can implement console output on this system.
I have in the past used the retarget.c/.h code from this forum that uses simple_uart...
Hi
I use the random number generator of LE1,I have made a demo code and the code can generate a random number.As the project in attachment.
I want to get a random time...
Hi all
I get LE1 enter sleep mode(PWRDWN = 0x04;)and use RTC to wake up,but LE1 cann't enter interrupt function after RTC wake up.
If I just use RTC to run ,LE1 can...
Hi,
I am using a custom board with nRF51822 to transmit data. Everything works fine except the transmitting always stop after a while. I am using softdevice 5.2.1. I attach...
Hi,
i want to start timer 2 and read its value just before the radio gets active. I've seen in the nr51 series reference manual i can use task capture to set the current...
I am developing using a nrf51822.I need delay timer
that can be substitued for nrf_delay_ms().
in other words,need a task delay that can be taken some event from another...
Hi,
i'm reading through a document that is part of the ble-sdk-arduino
The document is titled "HID over GATT maps USB HID to the bluetooth Generic Attribute profile...
Hi,
I have 2 timers and APP_TIMER_MAX_TIMERS = 3. I am getting NRF_ERROR_NO_MEM error.
If I increase to 6 it works. Is it 3 APP_TIMER_MAX_TIMERS per timer?
Thanks...
