dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I am using Segger embedded studio 3.1 with SD132 2.0.0 and a nRF52832QFAAB0.
I have verified that I am compiling against the correct header files. This service number for...
Hi, even if I set hal_nrf_enable_ack_payload(false) on the sender (and receiver), the receiver still sends back an ACK which i can detect in the NRF_ISR(). is this normal...
Hello,
I have a pca10028 and I am wondering if I can use it also to flash nrf52 boards.
I quickly tried with rknrfgo on mac to wipe a custom board based on nRF52832 and...
Hello.
I decided to use an external solution for RTC.
Sometimes the RTC chip offers an buffered 32.768KHz output.
Can I use this output to supply the 32.768KHz to the nRF52832...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hai
i am using mbed to program my nrf5188. now i am using securityManager to implement a bonding between central and peripheral. now i need to know when a device is connected...
Hi,
In my code, I have not started the HF clock. I call the ble_stack_init where "SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);" is called. Which HF clock...
Hi, all.
I tested ble_app_uart in example directory by PCA10040 board.
The ble_app_uart includes "printf("\r\nUART Start!\r\n");" and "UART Start!" cames out on the putty...
I have a scenario where I have multiple peripherals (nRF52) and multiple centrals (cell phone).
The user is going to use only one central with only one peripheral together...
Hello
In case a connection is disconnected locally by calling sd_ble_gap_disconnect(), no BLE_GAP_EVT_DISCONNECTED is fired even though the sd_ble_gap_disconnect() function...
Hello, I'm trying to optimize power on HID Keyboard app.
This post was helpfull but yet some questions remains.
If I use several services, and want central to be abble...
After S110 7.1 ble_stack_init(), any read/write to temperature register cause a HardFault.
Some sentences like:
nrf_temp_init();
NRF_TEMP->TASKS_START = 1;
...
Hi --
I am using the ble_peripheral/ble_app_hrs example project. And if I try to update the vs_uuid_count param to 2. It proceeds to fail the softdevice_enable with error...
