Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi There,
Under what condition(s) would a master skip a Connection Event (i.e. not transmit to the slave)?
We are currently testing using v12.1 SDK. I have configured...
After connect I try to find a service using MasterEmulator method DiscoverPipes() . I'm using event masterEmulator.LogMessage += OnLogMessage; to print logs. First it write...
I'm trying to implement an application where one board updates another board with Nordic's DFU service. I'm using the NUS client example as a basis to develop the BLE central...
Hello,
I am working with the nRF52 Development Kit and the Enhanced Shock Burst Protocol. I am trying to send Data from one Development Board to the other with static Payload...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Hi,
I want to check if the FW is properly loaded into the chip and the chip is locked. Reading APPROTECT hangs the chip even if SD is not enabled. I assume APPROTECT is...
Hello,
I work on application (written in C, compiled with GCC) which use pc-ble-driver 1.0 and nRF51822QFAC with the ble_connectivity (S130 v2.0.0) as BLE Gateway. I need...
Hi,
Anyone around that has good experience designing nfc antennas?
I'm in need of a pattern that is about 50% the size of the flex that comes with the nrf52 kit.
Doable...
Hi @ all.
I have a strange behaviour that I can't get rid of. But first some specs:
SD130 (2.0.0)
nrf51822
SDK 11
custom board
I have an application...
Hello, I'm south korea student in dongguk univ.
I use keil uvision4, nrf51822, s110 softdevice I need check the run-time.
ANd i like to check the runtime.
So i used "app_timer_cnt_get...
I am nrf51822 QFACA1 chip with s130 softdevice using nordic_sdk_11.
ble_connectivity example was not working and i am unable to do a scan from my application board.
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
Hi all,
I have just buy a product use nrf51822 chip, I tried to find out SWIO and CLK pin out to flash but can not. Device only has RX and TX pin for Uart function, so I...
Hi.
I use nRF52 and I want to use DFU.
I want to make init packet because DFU need it.
To make init packet,
need master control panel.
I want to know how to get...
Hi There,
Is it possible to modify the number of BLE frames per connection interval (CI)? We are using nrf52832s and are only seeing one master request and slave response...