Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Hi all,
i am using V11 SDk,
my task:
One board should broadcast continusuly.
if there is any neighbour is broadcasting ....then that will capture those data too...
Hi,
I am working on adc module of nrf51,through adc i am taking data and storing it in array.now i have to crossexamine this adc data with the prestored data and have to...
We are trying to complete Bluetooth qualification on our Cycling Power Service (CPS) against the Bluetooth Test Specification (Document Number CPS.TS.1.1.1).
We fail the...
We have been working on a project that requires the following separate segments be programmed to the board:
softdevice hex file
app hex file
UICR hex file
...
Hello,
I'm currently porting all my C++ code from SD130 SDK10 to SD132 SDK12 and I also upgrading from device_manger to peer_manager.
I've noticed that in peer_manager_types...
Hello,
It seems that NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE has wrong documentation. In sdk_config.h it says:
// <o> NRF_LOG_BACKEND_SERIAL_UART_BAUDRATE - Default Baudrate...
Dear Nordic Team,
Thanks for support.
I want to know the possible for nrf52832 act as a sniffer. If it is possible means i want to latest sniffer hex code.
Dear Nordic Team,
Thanks for support.
I have tested Current Time Profile sample application whenever connect with nRF connect APP the debug widows shows always "Current...
Good morning all,
We have a circuit based on 51822 chip.
We are currently trying to monitor some value from 0v to 24v from the analog inputs.
It's working, however...
I recently saw that SDK12.0 provides a Bootloader Cryptography module. I'm not certain after reading the documentation that this module can support my use case:
infocenter...
Hi,all. i want to use nrf51822 to generate a 3.3M hz wave,but i don't know how to do this.Can this chip reach so high frequency？Can someone help me? Thanks ！
I'm trying to implement context switching from handler mode to thread mode using PendSV. I set the PendSV pending bit inside an ISR with SCB->ICSR = SCB->ICSR | SCB_ICSR_PENDSVSET_Msk...
Compiling nordic project I get errors:
compiling main.c...
..\..\..\main.c(37): error: #5: cannot open source input file "softdevice_handler.h": No such file or directory...
I am not sure if this is a limitation with Keil or Nordic SDK. I made another copy of ble_app_uart inside SDK_11 s130 and renamed it with a much longer name. I tested that...
I'm using the nRF SDK5 v11.0.0.
I'm trying to test out UART Logging in the simple blinky example bundled in the SDK.
I added NRF_LOG_INIT() and then a NRF_LOG("Testing\n...
