I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Introduction
I use fStorage to write some data to flash and I read the data by following procedure:
uint32_t Read32(uint32_t address) { return *(mpFlashConfig->p_start_addr...
Hi i have problem i can flash via st-link but when i want program nrf52832 via bluetooth(smartphone). i create zip with bootloader, softdevice and app and that zip send to...
Affects nRF5 SDK v13.0.0 - v15.0.0
I noticed a minor bug in peer_manager.c, lines 972-975 (v15.0.0). Looks like an opening brace is on an incorrect line, see line 5 in...
I'd like to share a SPI bus between the nRF52840 and another IC. The chips are on different load switches, though, and I'd need to communicate over the SPI bus with my other...
Hi!
I'm New to BLE Mesh and i would like to implement Text Data Transfer and receive to multiple BLE's using Bluetooth Mesh on nRF52832, Can anyone suggest me how to get...
hi:
I am now using nrf52832 development bracelet, I have nRF52 DK and nRF6707,Using the latest version of PPK software testing，I am now ready to use PPK to test the power...
Hi Guys,
I'm doing the RF test based on nRF24le1, could you share any good antenna sample for this chip?
i found a TI 2.4g antenna design http://www.ti.com/lit/an/swra117d...
SEGGER EMBEDDED __align(4) have error info.I can use __align(4) normally, but there is a error information in SEGGER embedded
this error is "expected declaration specifiers...
Hi Nordic Devzone,
I'm working with nrf52-PDK and Mesh SDK, I wanted to know that if it is possible to send and receive some data at the same time?
And if I can do that...
I have made a custom board by following the reference design given in the nordic website using 2450BM14E0003 Balun and 2450AT18B100E chip antenna from Johannson technology...
HI,
My application is based on on your example ble_perepherical/ble_app_uart.
I realised few modification.
Now, after a BLE timeout, the circuit doesn't sleep anymore...
I am requesting timeslots with an interval of multiple seconds. But sometimes I want to switch to an interval of several milliseconds. How can I cancel the pending timeslot...
Using some of our nRF51 dongles as sniffers to debug BLE.
Sniffer software --> "w" --> Wireshark, no problems.
Post processing wireshark export *.csv files. No problems...
Hi.
Is there some code example for Bluetooth button for PTT aplication Zello ?
When I press a button BLE should send notify event =1, when released BLE send notify event...
