Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
hi
after success dfu operation the firmware start to run
then i am getting stuck write after err_code = sd_ble_gap_device_name_set(&sec_mode, new_name, DYNAMIC_NAME_LEN...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
Reading the nRF51 RM. On page 82 there is this:
But it doesn't make sense to me to talk about the LSByte of the PAYLOAD field, as it's just arbitrary data, and the Radio...
Has anyone had issues with connecting to the nrf52 DK with linux hcitool? I am able to see the device's MAC address and name (using HRM example design) with hcitool lescan...
I have everything working nicely with gcc, my own Makefiles, and the Nordic SDK12.2. I'd like to move to CMake to better automate my process (in particular, compiling one...
Hi
for few days I seem to got stack in using together UART and radio on nRF21LE01 in ESB mode
and I suspect irq_flags = hal_nrf_get_clear_irq_flags(); to be cause of my...
hai,
i am using mbed to program my nrf51822.
i need the following requirements
1.store some data on nrf51822 flash memory using pstorage .
2.setup bonding for security...
It's my question. I use saadc single mode from nrf52832 to sample voltage .When the original voltage is 24 V ,measurement of the pin is 2.8v,I set the resolution to 10 BITS...
hi,dear engineers,
i use the example experimental_ble_app_buttonless_dfu of nRF5_SDK_13.0.0_04a0bfd,
on the PCA10040 board,Now,i'm sure that I am flashed Softdevice,app...
hi
I have designed a small PCB with the NRF52 chip on it and kept few ports for some peripherals. Apart from that I only have 4 pins that I can connect to, UART-Tx, UART...
Hello,
I'm wondering if my nRF DK51 is not broken as it behaves quite strange when trying to connect with a BLE Central (iOS and Android devices). For most of the part...
I am trying to track down a power usage problem with my code. When I started using SDK 13.0.0/S140 v5.0.0-2.alpha on a PCA10056, the power usage went up in my app. I see that...
I'll try to simplify my project as much as possible to make this understandable.
I'm wiring an nRF52 PCA10040 board to an iCE5LP (Lattice) FPGA.
I'm having an issue with...
I have an after market breakout board for nrf51822 with a usb-to-serial chip (cp2102) that I bought from Amazon . It should act as an NRF51 USB dongle (pca10031-like) but...
