Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hey,
just wondering if its possible to lower the pwm driver clock of the nRF52832 to around 500Hz? Im working on a LED dimming application and the LED spots i use have...
Hi,
I got a error fatal awhile after the app switched to low advertising.
Could you please tell me where I can to look into ?
I got the error code 8198 from sd_power_systemoff...
Hi everybody,
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2.0.1
I found it really difficult to write DMP driver for nRF51.
I've already downloaded motion_driver_6...
Hi,
I have been modifying the MQTT Publish example for a product and found that the PUBACK message does not produce an event. The problem is in components/iot/mqtt/mqtt_transport...
I am trying to start development on the nRF52 Dev board PCA10040. However after updating to the latest nRFgo Studio 1.21.2, I cannot seem to program the board. I'm simply...
Im doing a porject using nRF51 DK,nRF51822 Bluetooth Smart Beacon Kit and nRF51 Dongle, with Termite 3,2 to view data. There's a few questions i want to ask.
My program...
Hello Nordic Team,
My question is about nRF51-Dongle.
As far as I know, this dongle is similar to the nRF51-DK (e.g, PCA10028), however, I would like to know if Nordic...
The following steps i used to Flash my nrf52 DK with DFu Serial secure.
Downloaded and installed
a)nrf5_SDK_13.0.0 b)nrfgo Studio c) keilv5 d)Python 2.7.9 e) pip...
Hello everyone, i have get nRF52840-PDK and now working on it. I use SDK 13 and SoftDevice S140.
My Project base on ble_app_template and i want add my service in this Project...
Hi,
I am currently using the NRF52 in a serialized application, with the SPI bus. I am using the SDK 12.1.0 and the softdevice S132 V3.0.0
My application is running...
Hi,
Can I use TI (cheap module 2451) as experimental blinky with central NRF52832.Don't need send button command , only UUID (TI:FFE0) check.It is possible?
Thanks
Hi all:
I download nRF51-ble-bcast-mesh from GitHub ,and put this project under below folder
...SDK8.1.0\examples\nRF51-ble-bcast-mesh-master\
compile this example...
