Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi
I am working with nRF52840 , since it is said that it can work on 64Mhz, i just want to confirm by using Oscilloscope.
You have any inputs that how i can check the...
Hi,
I am newbie to Nordic and I am building a program that samples adc value. I just wanna know about the difference between two functions "nrf_drv_adc_buffer_convert"and...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Does the S110 v7.0.0.3-alpha DFU bootloader support nRF51822XXAB (128k) part?
I'm trying to flash the DFU bootloader on my custom PCB that contains a nRF51822XXAB part...
Hello
I have an application to process advertising report even if it is duplicated.
Is there any way to control whether the soft deice shall filter
duplicate advertising...
Hello,
I am using the example "ble_app_beacon", I have compiled and tested (all works well).
I am wanting to add more data to the scan response by passing more data to...
I'd like to run a softdevice application with OTA support on a RIGADO BMD-200 Evaluation board . I've successfully flashed the softdevice, the app, and the rigado bootloader...
I have a simple application which pretty much consists of the following main function:
int main(void)
{
SOFTDEVICE_HANDLER_INIT(&clock_lf_cfg, NULL);
ble_enable_params_t...
Hi,
We're working on BLE communication between iOS and 51822 and found a data reliability issue. We have a custom characteristics that iOS read 60 bytes data from 51822...
Hi,
I have made some changes with how we update tick timer inside FreeRTOS and the results are promising
.
The improvement is
RTOS tick will auto correct if masked...
I went through a similar post for nrf51 which explains the numbers pretty well ( devzone.nordicsemi.com/.../) . I wanted to know what the values are for nrf52. The internal...
We have a nrf51822 device that has to send 6 bytes back to back at 12K8 and 6-18 bytes at 38K4 in the future.
The bytes are in an array and do not need to be generated...
Hi experts,
I have just tried lbs example. I saw in the ble_lbs_c.h, the base uuid and service uuid are defined for the peripheral peers who are going to be connected....
