Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh.
I based my development on the Light Switch...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
Hi,
I am currently implementing the protocol for a serial DFU, following the instructions given here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi all!
TL;DR
Is there a way to start 2 timers in 1 instructions ? (or to synchronize them afterward?)
- - -
Background
I need to take 8 timestamps of GPIO edges...
Hi,
I'm using S112 v6.0 with SDK 15.0 on nRF52810. It's based on app_ble_uart example. I have some data to save in flash. I define the address as follow:
#define PAGRE_TO_ERASE...
I want to extend the Thread Cloud Client Example (thread_cloud_coap_client_pca10056) with a peripheral controller. And I am looking at the UART Example (ble_app_uart_pca10056_s140...
Hi,
I will connect nRF52840 with other BLE module (ESP32) and they must exchange data (at first aproximation 20-50 bytes each 1-5 seconds).
I need to acheive lowest power...
nRF52 DK,software is nRF5_SDK_12.3.0_d7731ad,I'm using the example of "ble_app_multilink_central". SoftDevice is "s132_nrf52_3.0.0_softdevice.hex"
The BLE device is advertising...
Hi,
There is a racing issue in file: nRF5_SDK_for_Thread_and_Zigbee/components/iot/background_dfu/transport/coap/coap_dfu.c in function:
Sometimes calculated dalay is...
I'm trying to merge uart example in nrf5 sdk with light switch server example in mesh sdk
but I'm only facing these 2 errors :
when Linking uart_pca10040.elf:
Output...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I just wanted to know that What is the wake up procedure of the MCU when we call the sleep...
Hi,
I have a trouble trying to start development process on my NRF52840 DK.
Following the instructions
https://www.nordicsemi.com/eng/Products/Getting-started-with-the...
The nRF Connect application can not search the device after I modified the Rx, Tx pin in my own PCB board.Can anyone tell me why?
The UART can run well,but the application...
Dear Sir/Madam,
I tried to add battery service to the sample "ble_app_uart", but the code doesn't send notifications to cell phone. I struggled for several days and try...
