Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I was looking for a way to connect multiple nrf52832 via ble and connect the master to a smartphone app. Right now I'm focussing on connecting two nrf52832 through BLE. Can...
Hi there,
I see the "Error 133 (0x85): GATT ERROR" in the nrfconnect App with an HTC U11 Life with up to date Android (8.0.0).
I tested the nordic ble_app_uart example...
I am setting up the Power Profiler kit as standalone, no DK, measuring external target, also use the Segger jLink as interface. With the 2.0 software, it could not connect...
hello ,
can anyone guide how to add custom service and charactericteristic and receive data from nrf connect app using handler
i am using
board :PCA10040
nRF52DK ...
Hello guys!
We have a new project were will have to use dfu ota for a custom made application on a nrf51 beacon. Since the beacons use legacy dfu we want a way around...
Hello! I am trying to advertise two 16-bit uuid's and a 128-bit uuid. I set up advertising_init as such:
I declared the following structures:
where "SENS_UUID_SERVICE...
I am using Fanstel BT832 module based on nRF52832. I am using ' nRF5_SDK_14.2.0_17b948a ' with ' s132_nrf52_5.1.0_softdevice.hex '.
I am using this module as the BLE peripheral...
Hey Dear Nordic Devzone,
Here I am again, it has been a long time. Before I was working with the nRF52840 and Segger Embedded Studio. But as of now the company I am working...
i have programmed a arduino to send data(int value) on tx ,rx pin .How shoul i set up the nrf52 (the pin no of rxd and txd on nrf are p0.6 and p0.8).Which example should i...
Hi,
I'm looking into the reliability of the BLE connection from one nrf52 to another nrf52. I'm looking to understand a few things.
Once a connection is established...
In both the SDK and production specification (PS 1.4) it is noted that the TIMER (Timer / counter) peripheral in 'COUNTER' mode (0x01) is deprecated.
For implementing a...
In my current case there is a relay node to which want to send RSSI values of beacons nearby and then relay the same information across other relay nodes in the network, So...
