Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have a central application that I need to add a peripheral role to. I don't need to pair or bond in any of my connections, so I based my app on the ble_app_uart_c example...
Hi,
I'm currently running two separate TWI-instances on my nRF52 DK with SDK 11.
Each instance runs quite well with no issue, except for when instance 1 becomes active...
Hi,
When nrf51822 is connected via bluetooth LE to an iPhone application, is it possible to check the actual connection interval (between MIN_CONN_INTERVAL = 20ms and MAX_CONN_INTERVAL...
I have a project on a Ble Nano using Nordic SDK 8.1 that I currently compile entirely from terminal using a Makefile. I want to convert this project over to use Keil so I...
Dear sir,
I want to use NRF24LE1-F16Q48-R7 as a standalone controller in one of my application but it is not available with any vendor .
We want to use this For Low...
i want to know why there are 2 pages reserved although i mentioned i configured the number of pages to 1. It is used for what ? In fact, I need only one page for my data,...
Hi,
When compiling my program on SEGGER embedded studio I get the error:
Compiling ‘main.c’
main.c
expected expression before '{' token
in expansion of macro 'NRF_DRV_ADC_DEFAULT_CHANNEL...
I'm writing a central app using the pc-ble-driver project with an nRF51 dongle. This is to test our product, which is a peripheral using the nRF51822. The test central needs...
Dear All,
I have developed a BLE system in which nRF52832 is being used as a peripheral and central concurrently. I am also using BLE_GAP_CONN_SEC_MODE_SET_ENC_WITH_MITM...
Hello,
I have board pca10040 V 0.9.0 2015.41. When I program nrf and then issue a nrfjprog --reset -f NRF52 everything works fine, however when I execute nrfjprog --pinreset...
I don't understand OOB used in BLE security part.
Is this a communication out of 2.4 ~ 2.48 GHz frequency band?
Or is this one of method of pairing procedure(to generate...
Im currently working on a project and long story short im stuck on getting the nRF24l01 to communicate. I believe I have the Tx side of things working, however as I do not...
Hello,
We have connected Nordic+ MPU 9250 and able to read sensor values through UART display, but we wanted to do some excercises and read values, but it's not possible...
Nice to meet you.
The chip uses nRF 52832.
MDK keil μVision V 5.22.0.0 is used as the development environment.
Since I confirmed the operation with the sample project...
Hello Nordic team,
I'm doing a migration of my nRF51822 (32 RAM / 256 Flash) application from SDK10 (s130_1.0.0) to SDK12.2.0 using the s130_2.0.1. So I took the experimental_ble_app_buttonless_dfu...
