Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
When I was using a master slave integrated host, when I quickly disconnected the connection and then set up the connection immediately, it was found that the original disconnected...
Hello,
is there a simple example for reading out a value? The nRF5 is in this case a BLE peripheral server. The central device should only read one value at a certain time...
Hi:
I output a PWM channel in 16kHZ,i found that when i set the duty cycles 50%,my tft screen(i2c) display at a very slow speed,and it will be OK when i set duty cycles...
Hi,
I am trying to add a notification charactersitics on client, I am able to add one of them, but when i try to add another one sd_ble_gattc_write(), result is always NRF_ERROR_BUSY...
I am trying to use my nRF51 Dongle (pca10031) as a central.
I downloaded the nRF5_SDK_12.3.0_d7731ad and I could see that there is no BLE project for pca10031 (only pca10028...
i used nRF5_SDK_14.1.0_1dda907.
ANT protocol :
I used ant_background_scanning example.
I want to scannig device ID of hrm, bpwrt and bsc.
Then choose the device ID...
Looking forward to using the new sdk v15! Is there a plan to implement a new Bluetooth Developer studio plugin or should we go ahead and keep using the current version? We...
Hi, I encountered the following error in keil v5.12.0.0:
linking... .\_build\nrf51422_xxac.axf: Error: L6218E: Undefined symbol nrf_drv_gpiote_in_event_enable (referred...
Hi,
During SD+BL OTAU form SD132 ver 3.1.0 to SD112 ver 5.1.0, Old bootloader copied new one using function nrf_dfu_mbr_copy_bl(uint32_t * p_src, uint32_t len); to bad address...
Hi,
I have nrf52840 DK, I am unable to find details of which debug pin connected connected to respective controller pin.
basically dev kit has 10pin "Debug input" I want...
I tried following steps as mentioned in the tutorial, but after adding " ../../../../../../components/device " to the User Include Directories it looked like this..
But...
Hi,
I successfully installed and test pc-ble-driver with connectivity_2.0.1_115k2_with_s132_5.0.hex on PCA10040.
When I download ble_connectivity_s132_uart_pca10040.hex...
Android nRF Connect app DFU is flakey on my phone, a Motorola Droid Turbo w/Android 6.0.1. I tried with a Moto X and it worked fine, but on my Droid it rarely downloads successfully...
I'm using 52832/S132 V2/SDK11. For the test I only send notification to central just to see how many I can send in each interval. I keep calling sd_ble_gatts_hvx() until I...
Hi, I am having some issues. Just getting started with the nRF51422, so forgive my being a bit "green."
Background: Testing with nRF5_SDK_12.3.0_d7731ad, Keil V5.18A on...
