Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi sir
If nRF51822 unexpectedly enter DFU OTA mode, did boot loader have timeout counting to exit DFU?
Besides, if nRF51822 entered DFU mode and didn't update new firmware...
Hi all,
This 60-second limit is not enough for us. Our application is 48 kB & takes 35 seconds to upload. It should be enough, but the problem is that our iOs app does...
Hi All,
I use S120 device to monitor advertising and output the mac address,RSSI information via UART to PC terminal. The PC terminal can receive data continusly from the...
I found ble_dfu.py referenced in some posts to help automate the generation of an application.dat metadata file used (along with the application.hex file) to create the input...
in the code below, the keil IDE is flagging with red squiggly APP_BUTTON_INIT, claiming that it is an undefined symbol. It also says that this implicit declaration of 'APP_BUTTON_INIT...
Hello all.
while trying to calculate the data rate from bluetooth low energy , i have two questions
Is there a possibility to measure the data rate by using nrf sniffer...
I have an algorithm which does quite a bit of number crunching. I'd like to know how many clock or instruction cycles this algorithm is using. How can I get or calculate the...
Hi all,
I am not sure what to do now. I have been trying to get the s130 working with the device manager. I tried using github.com/.../nRF51-ble-app-hrs-s130 with sdks...
Hello,
in my application i use a bootloader for S310 and S310 V2.1.0.
The Bootloader is configured to use NRF_CLOCK_LFCLKSRC_RC_250_PPM_4000MS_CALIBRATION and the application...
Hello Everyone
I am using two application timers one of standard battery service and one i have made for adc sampling like this along with the code added for battery timers...
When I update the advertising data from the radio pre activation hook (800µs), the updated data does not appear in the advertising event following 800 µs after the hook is...
Custom Board with MCU NordicSemi nRF51822-QFAA
Softdevice S110 7.1
IAR for ARM 7.1
SDK 7.2 using a merged service (HID keyboard example + NUS example...
As per the steps given to program bootloader to the device i have programed it.
But the code is not getting executed i.e advertising nor led initilization is taking place...
Hello im trying to connect to a slave on BLE_GAP_EVT_DISCONNECTED event.
Can i use sd_ble_gap_connect(...) on this state, im getting error code 0x3202.?
regards, Vo...
Hi, I have bought the nRF51 development kit. I have downloaded source code for nRF51822. This comes with LOTS of examples but I suspect the codes are not for my board. Is...
