Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Please can any one tell me that how to recognize the sdk version of that we are used it can be predict from softdevice version?
for ex. •S132 SoftDevice v2.0.0 is used in...
Hi,
I am working on a project that includes eddystone format. I am using SDK v13 sample example. When ı try to disable auto relock feature, ı cannot read or write any adv...
Is there any way to print all SDK documents at once?
I'd like to print all of the SDK v12.0 Documents and carry it with in offline,
But I can hardly find any PDF Document...
Hi.
I'm trying to figure out how to properly use GPIO pins, but so far I did not find a document explaining how to use GPIO with nrf included functions.
I found bits and...
I am using nRF51 (PCA10028) DK and nRF51 SDK v9.0.0 for Development. I want to merge all three DFU(BLE + SERIAL + ANT). i have merge BLE and SERIAL DFU code. For this i have...
Hi,
I merged 3 hex files(softdevice.hex, bootloader.hex, application.hex)
I uploaded this hex file to nrf52382 DK.
After uploading hex file to DK, although there...
Hai
i have the following queries about pairing / bonding in nrf51822.
can i retrieve the bonding information from flash memory. if so how can i do that..?
if a...
Hi
Last year I got a nRF52 devboard and I modified the ble uart peripheral example to flash a led depending on what it recieves from nRF uart app.
It all worked fine(after...
Hi,
I'm trying to use the SPI example from the SDK 11 to comunicate with a MPU accelerometer.
The first time it works well, but then the clock send only 8 peak, so the...
FIrst timer with the nordic.. so i could use some help.
i've tried my code on the eval kit and it worked fine. On my custom board (has external 16MHz crystal www.digikey...
I've come across a couple of products that shows up as both classic and BLE. But when connecting to these products via nRF Connect or inspecting the traffic, I can't seem...
From reading the reference manual, product specification as well as searching the developer zone: here and here . Is it correct that the AVDD pin supply's ONLY the radio....
I have a strange problem with the secure bootloader.
After a succsessful DFU update of firmware, the firmware starts, but resets after a short while (about a second). ...
