Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
Hello,
I'm using several gpiote interrupts in SDK 12.0.1.
I want to know the max number of low power input pins.
My configuration in sdk_config.h is like below.
thanks...
Hi,
I need to read more than 3 or 4 Bluetooth Heart Rate Sensors (like chest strap, arm band, and so on)... I need to do this using Arduino and some library.
Could someone...
I'm using the ble_app_hrs_adc_battery_measurement example ADC code in my project
However, I don't understand what these lines do
github.com/.../main.c
As far as I...
I am trying to add spi communication to the twi_master_with_twis_slave project because I need to communicate with two different sensors. I have included nrf_drv_spi.h and...
Hi,
in the NRF52832 documentation the TX chain delay is 0.6 µs while the RX chain delay is 9.4µs.
Does that mean if transmitting two packets in a row to the same receiver...
Hello everyone,
I have been using nrf52 IoT SDK for MQTT implementation. Everything works fine as long as I am publishing or receiving only one character i.e.
param...
In Bluetooth Spec (CoreV5.0, Vol6, Chepter6, Section1) it is mentioned that the random private address is generated periodically by a timer handler. I could not find any mention...
1.specification says that we should trigger EP0STATUS task to initiate the status stage for control transfer(read/write).
actually nrf52840 will auto ack the OUT TOKEN...
In Eddystone example in SDK 12.2.0, APP_MAX_ADV_SLOTS parameter is by default 5, but if I try to use less than 5, an error appears in es_flash.c because in the code, 5 slots...
hello there i want to scan particular device. so i am using whitelist. i change in hear_rate center code. but its not working. other unwanted devices are also scanned. i am...
Hi,
We are working with the nrf51822 on mBed platform
We have created the following profile under deviceinformationservices
in main.c
uint8_t DataCounter = 100;...
Hi there!
I found out that there is some problem in the example ble_app_hrs_rscs_relay in nRF5_SDK_11.0.0_89a8197. I want to restart advertising when adv timeout. I did as...
I'm trying to use app_timer_cnt_get() to implement an RTC Calendar system on a Gigawit module (nRF51822).
I have a test app_timer that has presacler=0 and period=3 seconds...
This is no a question, but i was not sure where to post it.
I was trying to use the nrfjprog command with the new version of SEGGER JLink, but the terminal output was ...
Hi! I'm trying to work with the beacon kit, but I have some confusion about which type of sdk I can use because with some example that I have found it doesn't work.
Besides...
