Hi
I had a device that did not start up - because it was waiting for the 32KHz clock to be stable.
So I tried to change the setting below from 15pF to 5pF and it started...
Dear forum, I am testing out the radio on the nrf5340 using two evaluation board connected to a SES setup, but the receiving board only gets garbage and the checksum is never...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi Nordic Team,
We are using the MIMXRT1050-EVK as the host and the nRF7002EK as the Wi-Fi module with an SPI connection. However, we are encountering frequent errors that...
Hello, please help. I want to use nrf54L15 to connect to Bluetooth devices (Bluetooth headsets or other Bluetooth devices) and test the throughput between them. Is there any...
Hello,
I'm having a serious issue with my nRF52840 board. Here’s what I already tried:
What I have done:
Verified working USB cables (data + power).
Installed...
Hello,
I've tried to implement a custom service with a custom chacteristic, that shows the values per notification in the MCP (Master Control Panel) in percentage.
I played...
Hi,
I am using NRF24L01 module and I would like to transmit I2S signal through this module. I used SGTL 5000 audio shield for converting audio signal from microphone to...
Hi,
I'd like to determine the cause of a watchdog reset. I was hoping to utilize the WDT event handler (passed in to nrf_drv_wdt_init() ) to record the PC of the application...
I am trying to get the S132 Central Multilink example to run with 20 peripherals instead of 8. So far, I have made the following modifications:
In sdk_config:
Increased...
I wonder about the accuracy specifications in chapter 9 of the ppk user guide. It says +-20% of readout on average value. Is this only the calculated average of the python...
Using S130 to request notifications of radio activity as:
fails with NRF_ERROR_INVALID_PARAM.
Is there a reason this combination is disallowed? The use case for it is...
I would like to add the UART part to my application. But I will get these errors:
..........\components\libraries\uart\app_uart_fifo.c(109): error: #20: identifier "UART0_CONFIG_PSEL_TXD...
I am working on an automation project wherein I have to integrate ESP8266 with nRF51SDK. So, I want to serially send and receive strings over a physical UART connection, not...
Hello All
For our project we are using teensy3.6 as our main micro controller unit and NRF24L01 as RF transmission device.
Our project include mainly 2 parts
1) Data...
Hi. I've encountered a problem with some of my nrf24le1 chip (near every 5th piece) - current in deep sleep mode is very high (30-80 uA), if i change it to another chip, then...
Does the ui depend on the app design(nrf connect app) or on writing data in the characteristics. For the predifined i am getting a switch but for the one i added i have to...
Dear sir,
Sir I am trying to send an array of 40 values via nrf51422 to your andriod app "BLE SCANNER" by using the function "ble_nus_string_send ". But it is sending only...
I've tried ble_app_uart, nrf_serial.c etc. and none seems satisfactory.
I can write to the logger logger/uart during DEBUG, but it doesn't seem to succeed in RUN.
Question...
Hello,
I'm using :
- SDK 11 s132
- nRF52832
I want to protect my flash against dumping from swd but I'm working also with DFU from our custom app.
Is it possible...
Randomly on my nrf52832, sd_power_system_off() is returning NRF_ERROR_NOT_SUPPORTED and I'm looking for tips on how to figure out why. I'm using a Bluetooth soft device and...
