Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
On the included Thing52 example, the LED fires m_ioext_osc_status_change from an interrupt. Eventually, when it comes to requesting use of the TWI this comparison happens...
I've noticed that if I call app_usbd_cdc_acm_write with the length set to any multiple of 64 the data will not show up on my PC until I do another write with a value that...
Hi DevZone,
I am modifying an CAN library for nRF52840 preview DK. In my project, nRF52 preview DK is working as a SPI master and Arduino CAN Bus Shield is working as a...
Hi,
I am developing a device using the PCA10028 Dev Kit
It is configured as a BLE Central, SDK 7.2, SD 120
I am starting out with the example "ble_app_hrs_c_s120_pca10028...
Hello
Ive implemented and modified the light_switch_example and now I want to change the tx_power(sd_ble_gap_tx_power_set(uint8_t role, uint16_t handle, int8_t tx_power...
I am writing a program that waits for button 1 to be pressed. once it is pressed for 5 second it will call the LED ON api and when button 1 is pressed again for single shot...
i want to know which example in the SDK of MESH is the fast way make a demo to show this functon: use our moble phone to control more LED in same time.
remark: every LED...
Hello, I ask a question about power_manager() which is internally called sd_app_evt_wait(). I want the program to enter power_manager () to stop waiting for the event to come...
Hi guys,
we have triggered one interesting state of fds module… This could be somehow connected to https://devzone.nordicsemi.com/f/nordic-q-a/27259/fds-data-corrupted/107629#107629...
I have a problem with upgrading bootloader on NRF52832 IC. We are in the middle of porting our own bootloader from SDK 8.1 to SDK 14, because we had to change BLE modules...
Dear All,
while evaluating low-power options in the context of wireless sensors, I've stumbled upon a strange behavior with the nRF52832 using ESB from SDK 14.2. Here's...
Hi
I modified the SPI master example to read an 16-bit ADC at 44.1 kHz.
While the HAL_TIMER achieves its ~22 microseconds quite good, the SPI driver is quite slow: the...
Hi!
I have an observer that listens for advertises from just one ble switch. I can control the leds on the nRF52 DK with the switch. Now i want to connect to nrf connect...
Hey guys,
I have been fighting with this for a couple of days and I am hoping someone can give me some insights as to what might be going on.
We currently use the nRF24L01P...
hi,
i am doing a project where i have to discover custom services on connected ble nodes.
i am using nrf52832 as central device and thingy 52 as peripheral device i have...
