In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
hi,
I'm designing a board with nrf51822 chip. this board work on 2450 lithium rechargeable battery and it contain an MCP73831T circuit which is responsible of recharging...
Good Afternoon,
I hope someone can point me in the right direction.
We've customised an NRF51822 beacon and made it into a sensor but there seems to be an strange error...
Hello all , please your help
I need please , a reference design of nRF51822 for minimum with CR2032 .
using a pcb antena . ( distance is 4M) + the JTAG lines ...
Hi,
I am trying to secure OTA in nrf51822 board.
For that trying to build bootloader file available in SDK 12.2.0 version at location nRF5_SDK_12.2.0_f012efa\examples...
Hello,
I'm working on a project for which I would like to interface bno055 with nrf51822 smart beacon using i2c/uart. Basically the beacon must extract sensor values from...
With calls to these functions:
nrf_drv_gpiote_init()
nrf_drv_gpiote_in_init()
nrf_drv_gpiote_in_event_enable()
I have a handler (interrupt) routine that services a CAN...
I want to create a whitelist on the Central device. Because there is a lot of peripheral devices around and I just want to connect one peripheral device. First I register...
We have been recommended to use RIOT OS for our application and have been going through the tutorials but it seems that accessing the GNRC API for low ping ip communication...
Hai
i am using mbed to program my nrf51822. i need to implement bonding in my application. for that i am using securitymanager. and i have changed DEVICE_MANAGER_MAX_BONDS...
I am facing the same issue regarding to this post "Custom Service Issue - devzone.nordicsemi.com/.../".
At least i could figure out the IRAM1 start and size as explained...
Hi there!
I have been working with serializer and have the below issue:
I am using sd_ble_gatts_hvx() to transfer 20 bytes in burst until I get an error (TX buffer full...
Hi all,
first I have to admit that I'm a total rookie in "electricity". I know BLE software-side but just started to learn the hardware stuff.
I just received my PPK and...
by writing servals data into flash ,the data is always is 0,
void fstorage_test(void)
{
ret_code_t ret = fs_init();
if (ret != NRF_SUCCESS)
{
bsp_indication_set...
HI,
I am using nrf52832 with softdevice 132. Using SPIS1 to get the sensor datas from nrf to AARDVARK for calibration. Whenever I send the data's from aardvark(using AArdvark...
Whenever I try to flash the device in keil, I get a no Jlink device found. I get a similar message when trying to connect to the device via Segger. nrfGo Studio just does...
