Hello, I just try to migrate our developing project from old parent-child build to sysbuild,
But when I build the project with non-secure cpu (with TFM), I get the <err...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Dears,
I have tried to install the nRF connect SW package on a Windows 7 32 bit system (different versions) but was not able to get the applications running. When installing...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hi
I am trying the nRF51822 Evaluation Kit for the first time.
I have followed the instructions in the User Guide v1.1. The blinky_example works fine, indicating that...
Have you also wondered how to get serial IO (UART) with nRF51422-EK via the Segger debug interface?
[list=1]
[ ]Plug Eval kit in the USB port.
[ ]In Windows open "device...
Hi,
i need to stop one of my Timer at the falling edge of a Pin. So i need a gpiote_interrupt, is this right? Can someone help me how i can do this? if i write something...
I have 3 inputs I need to sample every n minutes. I have an n-minute timer that can kick off the first one, but I need to run the second and third samplings in succession...
We are creating our own dev board.
What pcb parameters were used for the PCA10004-nRFgo PCB antenna radio module 2.0?
1.6mm?
1oz Cu?
impedance control?
I have not...
Hello,
We want to use the J-Link Needle Adapter for nRF51822
The attached (capture.jpg) is the pinout from the J-Link Needle Adapter datasheet.
the attached (capture2...
Hi,
I have a wired problem with the nrf51422,
I'm loading the code using the J-link into my board or the evaluation board (PCA10007) that I have, the code runs perfect...
Hi all, I met a problem with measuring lithium battery voltage. I used 1Mohm and 250Kohm divided voltage, and used the internal VBG voltage as reference, and used ADC0 as...
I'm using a nRF51844
I'm writing my own ADC reading routines because I can't find any examples, but I know how to code so that's not a problem. I just want to confirm something...
Hi,
does a code example or app-note exists that describes how to configure the SPI peripheral to use an ISR to transmit data to a SPI slave?
Thank you in advance!
Dear
Do you know of a "present" /not present" low cost 2.4 GHz RFID chip for static asset monitoring in WiFi environment. compatible with, and actively associates with 802...
I am trying to hook up nRF8001 to TI MSP430F663x via nRF2740 module.
All inputs seems to be controlled properly.
Once I release the nRF8001 RESET line, RDYN goes low...
Hi,
I have a simple battery powered remote control device with a NRF51822 and using the Gazelle protocol for communication with the host.
To save battery the MCU goes...
The last few weeks I'm working with the nRF51422 and run in to several TWI/I2C issues. All of them I could solve except an issue with a SAA1064 7segment display driver from...
