hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
We are a medical company utilizing the NRF51822 board with SDK 11 for our application. As part of filing for approval for our product from the FDA we are required to prove...
There is a corner case in pstorage_raw.c that can cause a deadlock between pstorage module and the pstorage system event handler. This in turn will cause all the future pstorage...
Hi,
I just implemented LESC Numeric Match on the NUS service for my peripheral device (based on ble_app_multirole_lesc example). I am able to connect to my device using...
I am using the esb_tx example on an nRF51 DK board modified to send BLE advertising packets at 1 KHz.
I am receiving the packets on a BlueTooth sniffer. The contents of...
Hi,
i'm designing a board based on NRF51822-QFAC chip and i'm using this antenna chip 2450AT43A100E and this balun 2450BM14E0003T .
I put the balun as close as possible...
I have __asm("BKPT #0\n") in my code. When running without a debugger, it seems to generate a hard fault exception (which I can tell because I have a hard fault handler that...
This week I worked myself to a series of what seemed to be problems boiling down to one issue:
The Notification Write Response is lost when bonding has to happen first. ...
I'm trying to save power on my HID keyboard application by disconnecting the Bluetooth link after some time of inactivity. As soon as there are keystrokes to send, the device...
The question has been answered before, but the answer references a document called nAN-29 at this link: www.nordicsemi.com/.../73843444 . Which doesn't seem to be working...
Hello,
We use the PCA00031 dongle running the MEFW 0.9.0 in our production environment to validate a sensors accuracy. The PCA is controlled by a C# test program using...
Could someone explain the pin numbering scheme in regard to the interrupt setup handler?
To be specific, what pin number should be passed to nrf_drv_gpiote_in_init for...
In the ble_app_att_mtu_throughput example for the PCA10056 I am getting a "fatal error in the include chain" pointed from the #include "amt.h" line in amts.c. Specifically...
Hi,
I'm working on a firmware that is used in a nrf51822. I discovered an unwanted behavior of my system.
When the system is in power_manage mode, it can wake up in two...
● device : nRF52832
● sdk : 13.0.0
● softdevice : 4.0.2
Hi,
I have a problem with change mtu size.
I changed mtu size in sdk_config.h, but android application can't read...
