Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
We're creating a program that advertises and reads scan requests RSSI values to determine distance of central device and display them using the onboard leds(1-4)...
We are currently evaluating use of NFC on a nRF52840 which should get powered via VDDH.
Section 7.3 of the data sheet states that NFC can be used in any power configurations...
Hi Nordic engineers,
I found a strange problem that NRF52840 voltage of io high level is just about 2.65v~2.71v. I am sure that the voltage mode is normal voltage mode...
Hello,
I'm attempting to solve some issues with my BMD-200 (nrf51822) not getting the SD BLE_GAP_EVT_DISCONNECTED message. I currently Don't seem to be getting this message...
Hi, I'm not able to find the memory layout of the nRF52840 without the SoftDevice. I'm working with the nRF52840-Preview-DK and the SDK v15.0.0. I don't need the SoftDevice...
Hi sir,
we use nRF 52832 with ESB protocol. and we use ACK to send payload to PTX , but we found must use the same pipe which PTX used pipe to send ACK .
so , I have two...
Hi, Okay I got my nRF52840 Dongle, plugged it in to my window 10, verified it shows up as USB device on window's Device Manger.
Checked and Red pulsating LED (LD2) was pulsing...
SDK : 15.0
Softdevice : 6.0
DK : NRF52_DK
Hi everyone,
Does anyone have a BLE example with C ++ ? (a beacon example or anything else) I would like to have the Makefile...
Hello everone,
I'm currently seeing about 10-11 uA additional IDLE current when the SPIS peripheral is enabled, but unused. In the nRF5 SDK v15.0.0, the SPIS example draws...
I was looking at the fstorage documentation for SDK 14.2.0 ( https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v14.2.0/lib_fstorage.html?cp=4_0_1_3_51)
...
Hello Good People,
I need your help to kick of my development. I am using nRF52832 and Mesh stack. I am having problem to understand how its working. I have gone through...
Hello,
I am using a nRF51422 in my work. I am focusing on reducing system power consumption as much as possible.
At the moment I am using a system where the Client (dongle...
I was using for some time my code with FTDI USB converter to UART.
Recently I got built new boards, all with IC top marking N52832 QFABB0 1717AQ
and whilst any other board...
I would like to use PPI in order to set out pin and start a timer at the same time, from software.
I cant find a way to create an event from software that will fork a START...
Hello everyone, I'm currently writing my bachelor Thesis and need to establish an iot (preferably mqtt) connection from my pca10028 with my PC as broker (i.e. with mosquitto...
