void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
These posts indicate there was a problem at least at one point with the S132 SoftDevice erroneously requiring FPU:
https://devzone.nordicsemi.com/f/nordic-q-a/8133/nrf52...
On line 301 of app_timer.c there is the following code:
// No more timers in the list. Reset RTC1 in case Start timer operations are present in the queue.
if (mp_timer_id_head...
Hello,
I completely don't understand how to increase the packet size in the ble_uart example (using SDK 14.2 in both sides)!
I have two NRF52 DK boards and nothing is...
Hi all,
I'd like to design using 2ch SPI of nRF52832(as a MCU).
So, How many SPI channels of nRF52832?
And, Inform me pins of SPI port of nRF52832.
Best Regards...
Hi
I am creating bond from the Nordic device to my Android APP.
But I want to change the name of the device immediately after the bond has been created.
i.e from NEWDEVICE...
Hi all,
I am using PCA10040 with nRF5_SDK_13.0.0 and using the ble_perpheral -> ble_app_uart example.
I am trying to stream data from UART to an android phone and the...
Hi,
Just a quick question about how the ble_app_uart works.
When sending to the UART from "static void nus_data_handler(ble_nus_evt_t * p_evt)" and also receiving from...
Interrupt or main() context, or something else?
We're using S140 SoftDevice, nRF52840 and Segger Embedded Studio 3.30
We're also usinq Quantum Leaps ( https://www.state...
Hi
I am use hids, ancs and hrs services together with bonding. Phone should hold the connection with device. I am enable heart rate sensor when notification is enabled ...
Hello,
Trying to make GATT services configuration for nRF8001 chip in nRFgo studio. On services.h file generation I see Generation of source files failed window with "Generate...
Hi, Nordic team:
Now, I'm using NRF51822QFAC in a production with the SDK 10.0, the firmware includes FreeRTOS and DFU, when start the DFU in nRF-Connect APP, it can't jump...
All standard SDK examples disconnect immediately once I try to connect to from Android device. But when I flash the same sketch to nRF52-DK, I can connect successfully.
...
