Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I am using SDK 14.1.0 S132 for PCA0040 board
i want to combine the next two examples:
examples\ble_peripheral\ble_app_buttonless_dfu
and
examples\ble_peripheral...
Dear experts,
How is the UCIR protected against rewriting?
I would like to store some ID's which I want to be sure they cannot be erased or over-written once programmed...
Hello,
I can see s110 api commands as a web pages on infocenter.nordicsemi.com .
Is it an api list of commands manual in a document like pdf, etc.?
Thanks.
We are trying to configure the I2S peripheral for working with the ICS-43434 microphone ( www.invensense.com/.../) , but we are having a hard time fulfill the requirements...
The product spec is not clear, what is the maximum current draw possible from a 52832? Please assume ALL features are in use and fully enabled.
Thanks.
Hi Dev Zone,
I am going to communicate my nRF52840 Preview DK with an arduino shield. I am checking the PIN number. According to the information about the Arduino board...
Hello, I want to switch the functions between beacon advertising to connectable advertising.
In the code , it can be initial as a beacon advertising or normal advertising...
Hi,
I am running the ble_app_beacon example in nRF52 DK (PCA10040). I can see the nRF beacon in nRFConnect app - but not in the nRFToolbox - Beacons. After opening the app...
Hello,
I am using WT51822-S4AT based on the nRF51822 SoC and I am trying to program it with the ble-beacon example from the SDK. Looking at the DK documentation, I need...
Hi,
Device- nRF52832 (nRF52 DK)
SDK version 14.2
SoftDevice version 5
Segger embedded studio.
I am trying get the BLE working, unfortunately calling nrf_sdh_enable_request...
Hi, Everyone How to turn on 4 LEDs in BLE ? I am testing ble_app_uart on nrf52832 (softdevice s132). Try to blink the four LEDs on the board do. I have added to main() bsp_board_led_invert...
Hi,
I want to create a custom GATT service. So I duplicate the example from the SDK ble_app_blinky. Basically what I did so far is rename all the "LBS" (ble_lbs, lbs_p,...
Hello, I am trying to store microphone data from the Nordic Thingy by modifying the Nordic Thingy Android app .
The Thingy firmware encodes the digital microphone data...
Hi there,
First of all, I'm pretty new to this, so next question might be obvious to others.
I try to decipher a line of code, and the little Part is what puzzles me...
