Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
we are using a custom board, with codes tested on a NRF52 DK. We reconfigured the pins and when using pin P0.09 (by default NFC) as an input "active_high" and with ...
Hello,
I've done this steps:
I erased the whole chip: nRFgo Studio/ DeviceManager/nRF5x Programming/Erase all
I programmed the Softdevice s132_nrf52_5.0.0_softdevice...
Hello Nordic Team,
i use SDK 12.3 and SoftDevice S130.
In the template project ( \examples\ble_peripheral\ble_app_template ), the BSP module is used to indicate advertising...
Hello,
For my project I need to send raw data (without prefix or timestamps ) along with system logs trough the same UART.
So far one possible solution is to use NRF_LOG_RAW_INFO...
I've been using nRF24LE1 for development. The HAL library provide the AES encryption for ECB mode. Now I need the decryption function. Does anyone has the realization? Any...
Hello everyone,
I use SDK14.2 and s132 softdevice. I can read "NRF_SAADC_INPUT_AIN0" and "NRF_SAADC_INPUT_VDD" pins and system is working properly.
Working Code like...
Dear friends,
I am using the nRF 52832, s132. I want to know the BER (bit error rate) of the BLE link. How can i measure it? Further, to what extent do other radio interferences...
Hi.
I want to know the time difference between functions by using a timer instead of a difference. I've looked at app_timer.h, but it's hard to understand.
I do not need...
I am trying to use the ADC to take power measurements on an interval. I found an example to read the values out online:
void ADC_IRQHandler() { nrf_adc_conversion_event_clean...
I am designing a PCB using the NRF52832 and this antenna . The antenna design guidelines suggest ground clearance and direct traces from the NRF52832 to the antenna without...
I am working on a project which I wish to Paer between to nRF51422 devices and to use the auto reconnect between them. there won't be any display so it must be automatically...
Hi,
is it necessary to use internal regulator for NFC DC/DC or we can use normal internal LDO in design.
also if we need to use internal DC/DC regulator, what is the...
Hi, I have tried to find a solution for some time now in the Nordic Semiconductor forms.
We have been noticing a peak or a disturbance in voltage in every connection interval...
