Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I try to integrate the CoAP Server and TFTP DFU example code, and it works well.
[ENV]
IoT SDK v0.9.0
nRF52832 DK
According to the specification, the MTU...
Hi, dear support team,
I program the softdevice(S110,v7.1.0) to the nRF51822 devices(our product) by nRFgo Studio v1.21.1.3.
The nRFgo Studio shows a error message as...
Good afternoon.
I have 2 boards NRF51:
One as beacon (SDK 9), use example code "nRF51_SDK_9.0.0\examples\ble_peripheral\ble_app_beacon".
The other as...
Hi,
I have a problem using Secure DFU Bootloader available in SDK 12.1 on nRF51822_xxAA SoC.
Initilaly i was using nRF51 DK board and Secure Bootloader example in SDK...
Hello,
In our application, we do not use the antenna at Pin30.
However, in Nordic's Reference design in Github, even the simplest design (nRF52832_qfaa_dcdc) has an...
Hello,
Can I interact with the internal device of the nRF52 DK (PCA10040) while an other nRF52 connected through the P20 (or P19) connector?
The JLink tool has a "device...
I implemented an application to advertise indefinitely with APP_ADV_TIMEOUT_IN_SECONDS set to 0 and it works just fine. Now I want to
have a time out and set APP_ADV_TIMEOUT_IN_SECONDS...
Reading the nRF51 RM. On page 82 there is this:
But it doesn't make sense to me to talk about the LSByte of the PAYLOAD field, as it's just arbitrary data, and the Radio...
Has anyone had issues with connecting to the nrf52 DK with linux hcitool? I am able to see the device's MAC address and name (using HRM example design) with hcitool lescan...
I have everything working nicely with gcc, my own Makefiles, and the Nordic SDK12.2. I'd like to move to CMake to better automate my process (in particular, compiling one...
Hi
for few days I seem to got stack in using together UART and radio on nRF21LE01 in ESB mode
and I suspect irq_flags = hal_nrf_get_clear_irq_flags(); to be cause of my...
hai,
i am using mbed to program my nrf51822.
i need the following requirements
1.store some data on nrf51822 flash memory using pstorage .
2.setup bonding for security...
It's my question. I use saadc single mode from nrf52832 to sample voltage .When the original voltage is 24 V ,measurement of the pin is 2.8v,I set the resolution to 10 BITS...
