hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
in my application i am using the hrs application and added dfu and uart service to it.
Q1)how dfu service works?
For my board i removed the total flash so steps i have...
Hi i'm going to do a school project with bluetooth mesh network so i was wondering if bluetooth 5 supports it and what are the benefits of using bluetooth 5 over bluetooth...
Hello All,
Can i use nRF52810 SOC for mesh networking. is there any space constraints?..
if we can use can we control all the nodes via smartphone .
please provide...
I am using nrf52832 peripheral and ble central with some android application .if an app opens it we get ble disconnect event and if we kill the app ble_disconect will come...
nRF52840 OPS 0.5.1 lists the following highlighted sensitivity spec:
The Bluetooth core spec defines sensitivity for this payload length as a BER of 0.017%, not 0.01...
Hi
We are trying a Nrf51-Dongle in a school prosject here in Norway We need to use one of the GPIO pins on the Nrf51-dongle as input When this input is 1 , we want the dongle...
Hi ,I am using nrf52 DK with mpu9255.I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in keil v5...
Using nrf51422 in KEIL. I am verrrryyyy new to this type of programming. I have been looking at multiple examples within the nortic github to find how to input analog reading...
I started Heart Rate Monitor app "ble_app_hrs_pca10040_s132" on nRF52 evaluation kit (nRF52832). Everything work well when I connect with nRF evaluation kit from Android devices...
Hi!
I just got my PCB with a Telit BlueMod+S42 Module on it (nRF52832).
I' using the LESC feature and ist works properly on the PCA1004 and on the Telit DevKit (same Module...
Hello,
I'm working on a bootloader based on the example of SDK13.1. I want to add two more characteristics to the DFU service, but after I add them, the nRF Connect app...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Dear friends,
If i set the conection interval=100ms and the slave latency=1, the slave will wake up every 200ms. If the slave has data to send, it will still wake up every...
I haven't been able to find a drawing file for the nRF51 Development Kit. Is there one out there?
Ideally, I'd like to get the drawing and a *.STP file for SolidWorks.
