Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello!
I'm looking to build an application on nrf52840 DK that collects multiple sensor values and transmits it over Bluetooth. For now, I don't have a bluetooth application...
Hey I'm doing some SPI transfer in response to a GPIOTE in event. I'm targeting the NRF52840 and kind of went with the following answer:
https://devzone.nordicsemi.com...
Hello,
My setup is pca10040, sdk 14.2, s132.
I have tried firstly the blocking mode function and it is not reacting. After that I used SAADC module in a non blocking mode...
Is it possible to use the mbr, currently inside the softdevice, without the softdevice? Can we use the combination MBR/Application/bootloader? So we have a lot more flash...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
When completed my program is supposed to read data from sensor (via I2C), store it in...
Hello ,
is the NRF52810 surpport LE long range? is the mainstream mobile phone surppot LE long range? if i set the nrf52810/nrf52840 to be LE long range mode, and then ...
I am developing a product for indoor positioning and some thing else.
I want to know that how many beacon device can operate in same place.
As I know, beacon devices can...
All,
I already run BottonlessDFU example successfully after refer to below link. What's more, I added BAS and DIS service to Bottonless DFU example, and after use nrfutil...
Hello,
I found out that S/N from nrfjprog -i command returns the same number among different debuggers, all of them are 123456. At the same time, S/N showing from J-Link...
Hi,
I'm developing a peripheral that expose the HTS service.
I have the on_hts_evt event handler to handle BLE_HTS_EVT_INDICATION_ENABLED and BLE_HTS_EVT_INDICATION_DISABLED...
I am hoping to get solid verification that nordic offers a solution for sniffing BLE 4.2 packets.
The application I need to sniff is maxing out the MTU (250B payload) so...
i want to implement 2 hardware SPI communication in my code. i have one already working. talking with LCD ILI9341. the functions are using spi_write / nrf_drv_spi_transfer...
Our beacons are going into production, and to make function tests faster for our manufacturer we would like to transmit our beacon UUID, major, minor at a rate of 760ms for...
