Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I want to implement deep sleep (wake up using RTC at a particular time interval), and determine the current consumption in nrf52833 dk. So I used the sample code first. When...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Using latest SDK and toolchain 3.0.1, VSCode and nRF Connection Pack on Windows 11 I nearly never see a working nRF Kconfig GUI - only the first time directly after I had...
Hi,
I have a custom board for the nRF54L15. I have already implemented LEDs and a button, which work fine. But I cannot get the PWM peripheral working, and I do not understand...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hello everyone,
I’m currently developing firmware on our custom board based on the nRF52840, using nRF Connect SDK v3.0.0 and Visual Studio Code.
The board is designed...
Hi Q&A My keyboard chip is NRF52832, and the program uses ESB 2.4G communication. The receiver dongle uses NRF52833. Now there is a problem that when the CAPSLOCK is clicked...
I use nRF5340 audio DK,iso_time_sync example, can successfully send BIS data, then I use DK as controller, bumble( google.github.io/.../index.html) as host and it fails to...
Hi, I have a project which uses Matter over WiFi and at the same time running a HTTP client. I want to retrieve and use the WiFi credentials from the Matter over WiFi provisioning...
Hi,
When try to use timer based on nrfx ( https://github.com/NordicSemiconductor/nrfx/ ) directly on the nrf54l15 DK board, I found it never call the timer_handler( ). ...
