Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have 5 nRF52832 development boards.....
I'm using Visual Studio 2015 and a Visual GDB plugin.
I have loaded and built the BLE Le example.
I start the debugging...
I'm using SDK 12.2. The FDS operates on word-sized data. How can I ensure that my data structures are word aligned and multiples of the word size? E.g. if I'm trying to write...
Hi everyone,
I am looking for reports and/or certifications that can help with our own device's certification process.
Would you know where we could find such reports...
Can I configure security parameters my own way?
I read some BLE profile but there are not explain about security configuration.
And I tested by using PCA10028, iPhone4s...
I am trying to setup an interrupt to fire whenever any of 6 GPIO pins change value using an nRF51822 with soft device. I found the example that uses GPIOTE to get an interrupt...
Hi. I'm using nRF51822AC, SDK12.2.0. S130 v2.0.1.
I just want to make DFU program. But I think it's a little bit confusing. So I want some explain.
Q1. What is the difference...
I'm wondering whether I'm missing something.
This is the callback called from finish_transfer in both nrf_drv_spi.c and nrf_drv_twi.c.
This parameter is useful because...
Hi,
I am working on the examples\ble_peripheral\ble_app_uart sdk 12 example on SES.
I was first setting:
FLASH_START=0x1B000
SRAM_START=0x20001EB0
Then tried...
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
Hi,
My code always throws "NRF_ERROR_INVALID_STATE" error and reset in nrf_drv_gpiote_in_init.
I tried many pins all of them are free and not used:
#define BUTTONS_NUMBER...
Hello,
is there a way to check for NRF_ERROR_BUSY before issuing a new command?
The idea would be to create a timer to retry issuing a/the command if the NRF is not...
Hi,
After following all instructions on: gnuarmeclipse.github.io/.../
And after installing all Nordic Semi dependencies on eclipse.
I import on eclipse the UART_Loopback...
Hello team,
I got a DEV KIT NRF52
And I'd like to get all my LOG : NRF_LOG_* ( NRF_LOG_INFO… ) From my USB interface Serial:
/dev/tty.usbmodem1421
I made sure...
