Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I tried to make a special application that includes 3 advertisements, (one with softdevice, and two others with timeslot), then i successed to
integrate all the three...
Hi There,
I'm a beginner with Nordic products and I'm taking over the nRF52840 Preview Development Kit.
My final goal is to supply with a solar cell my nRF52840 running...
Hi,
We have issues with mBed's Thread::wait() in mBed 5.7.2, which causes our interrupts to stop working. Below is a small example that can be used to test this. By removing...
Hi. In the product I'm working there is a qi and NFC antenna on the same side. I resolved the issue of the qi charger overloading the nRF by placing a 1nF capacitor in series...
I enabled whitelist in my nrf51822 device and get my phone irk address after bonding then i hardcode that specific irk to my nrf device. Now i can only able to connect my...
I am using KDeveloper to program the nRF52, so far it has been working fine, but I want to be able ofdebugging and going into breakpoints, etc. What should I set in order...
I have programmed two boards(pca10056) with the cli example in thread sdk.I have set the first one as the leader and the second as the child but after pinging the kit the...
Hi guys,
I am working on a nrF52832 project and want to use Segger Embedded Studio since there is a license agreement for nordic based projects.
I am using freertos from...
Is it possible to communicate between 2 Nordic kits at 1 M baud without HW flow control? I came across this post in the forum which states that bytes can be missed when switching...
I am trying to use gcc to compile a c++ code for nRF52. I am using the TWI library and am getting the error below. Can anyone help me rewriting this macro so that it compiles...
Hello All,
I am using 32 pin nRF52810 chipset.
Crystal have two pin and it will work as in sch. (Xin and Xo)
when using Osc (which is an external clock generator) there...
Hello,
I'm trying to create a lightbulb custom HomeKit accessory by referring to the User Guide v1.7.1. I followed the exact same steps as described in the document for...
Hi,
* (i'am using sdk14.2 ans S140 V5.0.2)
i'am trying to inegrate a beacon application to my ble_uart example , so my purpose is to advertise ibeacon pachet format only...
We have some old stock of the nRF51822 pre 2014/8/20. Was there a change to the product around that time that would prevent us from using from using this stock?
Many th...
