I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hey!
I am working on NRF51822-QFAC, with the help of SDK 12.2 with the aim of scanning my bluetooth speakers and mobile phone.
For the same, I have loaded the project...
I want to change rx to tx mode and back after recertion my master NRF24l01 packet on NRF52 with esb, how to do it?
I tried this but it doesnt works:
void nrf_esb_event_handler...
Hello,
I am using nrf51822 and supply is provided through rechargeable battery. Please review my schematic and suggest changes if there is any.
Thanks,
Shailav
I used the following code to verify the working of the clock (at P04) of nRF24le1.
I used a 4.7K pull up resistor with a VDD of 3.3V, which was output from the nRF.
Note...
Hello,
I'm using nrf51822/s130/sdk12.1.0.
Before adding BLE code there's no problem in writing inner flash.
In main I just added below ble_app_uart codes(not modified...
Hi,
I have Wireshark version 1.10.14 and sniffer version 1.0.1. I send the data out from PCA10040 with connection interval of 7.5 ms and packet throughput of 200Hz using...
The pulldown on the SAADC is 160k. Is it ok to create a resistor ladder by adding an external resistor of, say, 400k, enable the internal pulldown and then input a higher...
Hi NordicSemiconductor's community,
I have a basic question about connection to a BLE peripheral.
I use the SDK_10.0.0 and s110_v8.0.0.
I want to know how to implement...
how to change RX and TX operations ?
i wrote next code:
#include "nrf_esb.h"
#include <stdbool.h>
#include <stdint.h>
#include "sdk_common.h"
#include "nrf.h"
#include...
Hello
I used one example from the nrf52 SDK and wanted to add another functionality to the code. How do I know what to add to that file?
Is there a global sdk_config.h containing...
I am migrating from SDK 12.2 to SDK 13 on Nrf52.
I use Eclipse.
I have a few questions:
In SDK12.2, there was :
Patch for SDK 12 - implements required workaround...
i am using nrf52832 dk. i am trying to change the flash address from 0x000 to 0x0002000. But i can only flash it to 0x0002000 if softdevice is already present on controller...
