Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
we are facing issue of "application program" hex file generation, which is different in two machine . we are matching setting of both machine , we found the difference in...
Hi,
I've got a problem with nrfutil package on Raspberry Pi with Python 2.7.9 and pip 1.5.6 included to raspbian distribution.
I'm writing like below:
pi@raspberrypi...
Using SDK 12.1.0 with flash containing data from a previous version of software.
The pages_init function in fds.c does no have adequate protection to prevent writing to...
Hello,
I have followed a couple of the posts on the devzone on how to increase the MTU and add the DLE support such as this .
However, whenever I send over 20 bytes...
hi, i have a SIM800L Core board which is using UART protocol to communicate or to send At commands. so that i am using BLE_APP_UART example to set AT commands to SIM800L....
Trying to follow this tutorial using KEIL 5.23, J-Link 6.14b and the DK.
I am getting linking errors like this when compiling:
What did I do wrong and how can I fix...
hi,
i was looking for example of two nrf52 communication. One is central of course and other one is peripheral. But i have following doubts.
If one is central then...
What is the right way of stopping and then subsequently re-starting SAADC?
Using the saadc example, I want to be able to stop saadc when a certain pin is grounded or when...
Hi,
I just found the following example:
infocenter.nordicsemi.com/index.jsp
There the baudrate 115200 is set by default. If I calculate the bit rate (8 data bits one...
Hello,
I use two NRF24LE1 emission and reception when I use a simple ACK is good but with ACK payload, there is a problem,
I do not really see where you can help me,
Thank...
In an answer to this question about current usage of pull-ups here , RK and Vidar comment:
Is the GPIO you have configured as a pull up, being pulled down? If so you...
How to save data persistently(non-volatile) to nRF51 core not effected by powering off and on?
(How to save static data persistently without deleted when the core is turned...
Hi,
I have just used some code from your flash_write example in the SDK, it works ok but i have a couple of issues, the code is from sdk 12.7, and the chip is an nrf51422...
I have a question about using the "Radio" peripheral on the NR51422 Dongle development ki
I am putting together a fairly simple prototype device that needs to transmit...
Hello,
I started development on a NRF52832 board couple of days ago. I want to get sensor's data via SPI (with the NRF52 as a master). However I've got weird linking issue...
