Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello, My SDK is NCS2.8.0, I want to know the version of matter, but I can't find it, may I know how to get?
BTW, does NCS SDK support Matter 1.4.0, if yes, could you tell...
In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used. Logs are having corruption.
Looks...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
Hi,
I happily use the JLINK UART interface which show up as COMxx on windows for both the PCA10000 and PCA10001.
We are trying to 'see' the same on Linux. Have inatlled...
Could you please let me know the current rating in between retries while transmitting.From the oscilloscope reading, that is not obvious. The documentation shows three idle...
Hi
We had some problems updating our devices with the nRF Loader App on IOS. After selecting the device in DFU mode the App hangs and aborts with a Bluetooth error after...
Has anyone been able to get the DFU over the air bootloader to work with gcc and the newest SDK (6.0)?
I have followed all the tips I can find on here to get it working...
I'm wondering if the timeslot API is planned for the s130 or if it's intended to be s110 only. If it is eventually getting added to the s130 is there a loose time frame for...
Hello,
i am using the nrf51822 with softdevice s110. In the spec i read that the contoller works as well with an external 32khz reference which i want to use. The oszillator...
hello everyone,
i use nrf51822 and i want to use one switch that wakeup the module from sleep mode. so can i connect switch to gpio of nrf51822 module. if yes than which...
I'm a newbie so bare with me. I had this code running, saved it, and started another project. I tried not to touch any of the files I had running with the example below, but...
application note nAN-034 describes two alternatives for production testing an application using the nRF51822. One method is using a commercial tester (MT8852) and the other...
I need to send data PIR motion detector sensor to the master controller in my motion detector network.
Can I get away with just one of the nrf51 chips and my PIR sensor...
We're trying to decide at what voltage we should run our nRF51822 on the next revision of our board. To date we've been doing fine at 1.8V. The current drawn on a 3.7V lithium...
hi, i made ble app including bootloader using nRF51822 (s110), sdk 6.1.0
when i use sd_nvic_SystemReset() function in app, it erase app's pstorage.
But i want to preserve...
Hi,
I use S120 as central device and I need to handle multiple connections.
However S120 works quite unclear to me.
If S120 doesn't reply to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST...
Hello ,
I am trying to develop an application using the S130 soft device using Keil MDK v5 Lite. I have came to know that it is not possible to generate a code size greater...
