Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Good morning,
I have taken a look to different information related to this topic but I'm still confussed about the way to proceed in order to implement the way of working...
I am trying to use the dynamic payload length feature, but I am not sure of what settings to use for the RX_PW_P0 - RX_PW_P5 registers. According to the documentation, for...
Hello,
We are going to use nRF51822 in our product.
Use case is as follows:
Connect with android/iOS phone and receive some configuration data.
Connect...
Dear Sirs,
I'm using nRF51822 EVKit and using example code "button_radio_example" for pca10001 device and measured current consumption on this PTX device and found out...
I just want to handle phone simple call event from iphone4s.
How can I do? Is there any other way to do this?
There are so many media key in hid profile, is there any...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi guys,
is it possible to get the mac address of the connected device?
Didn't find anything in ble_evt_t ..
Thanks!
Edit:
Sorry, i found it:
its in the ble_evt_t...
i am new to nfr51822 and i am doing project on indoor localization in which i need to read the RSSI values of bluetooth. so how i read these values? and i have setup the evaluation...
Hi !
I would like to know if there is a nAN-36-like application that also implements the radio functionity.
I would like to send a raw radio message to other devices...
HI：
I use Bluetooth capture crawl data. I want to see the data in DEBUG in?I can not see Adv PDU Header among type TxAdd RxAdd PDU-Length data in the code, AdvA which data...
Hello
I am developing a health fitness watch using the nRF51822 System-On-Chip. I am interested in acquiring an organizationally unique identifier that can be then be implemented...
Dear Developers,
At the moment I'm writing some software to develop an Android App. I'm using nrf8002. When my app connects to the nrf8002, I'm able to read battery level...
I am trying to use the nrf8002 for proximity type application. Right now I have a prototype working with a speaker and LED and I can light up either one using an app. What...
Hello every boby,
I'm a newbie in PIC programming and I hope something could help me to start interfacing the nRF8001 with a PIC. My schematic is already done but I don...
