My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello,
I am currently working with the nRF5340DK and the W5500 shield. Both work perfectly when using the dhcpv4_client application. However, when I attempt to use the recv...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
After some pstorage_update calls I start to get error 9. From nrf_error.h it is called NRF_ERROR_INVALID_LENGTH but from SDK doc it looks like pstorage_update does not have...
My question is in regards to BLE security. I have certain characteristics that I want to remain open. As they will be used to determine authentication at the application level...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Working through a custom security implementation. It is to desirable to know a unique identifier for each bond that has been made with the nrf51822 SD. When the SD enters...
I have several asynchronous аperiodic sensors with their interrupt handlers. My service should gather the data from those sensors and do some math. The outcome of this math...
Dear all,
I tried to program and test the iBeacon application on the s110 folder from nordic examples.
The code on the Cortex-M0 has problem. Seems during programming...
After program nrf51822,it works normaly.But when I program again,it can't debug.NO SWD and NO USB DEVICE.So I can't use nrfGoStudio or nrfjprog.exe to recover it.When I pull...
Hi,
I've set up a streaming solution that is easily streaming 4+kBytes/s to an iPhone. I've also set up an ADC service that is sampling at 2,083 Hz 10 bit mode, using a...
Hi,
I am using nrf51822 (128k).
Softdevice 6.0 (s110), SDK 5.2.
How can I send an empty notification packet (data length 0) to master device?
If I send a packet with data...
I was wondering whether it is safe to use a delay (such as implemented by nrf_delay_us) to, for example, delay an iteration of a while loop, or that it is always better to...
Dear Sir/Madam,
I am testing iBeacon application on the nRF51822 mounted on nRF6310 motherboard.
I programmed the ble_app_beacon application in the keil_v5\ARM\Device...
Hello,
I get a sample code in the dir flllowed after intsalling nRF51 SDK:
\Keil\ARM\Device\Nordic\nrf51822\Board\pca10001\s110\ble_app_beacon_code\main.c
but I still...
I ve installed CSR bluetooth 4.0 adapter , it can communicated with even the bluetooth 2.0 devices, how ever it even can not discovery the board when I programed the softDevice...
Hi,
I have ordered nrf51822 development kit with one of my local vendor. when the product came to india , it was checked in customs office somehow the samples in the kit...
I'm using an nRF51822. Currently, I'm using the low power sleep mode. The device uses about 1.5 uA in sleep, which is great. The firmware wakes up the device every n minutes...
