Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
In the API, the user gives the 'distance_us' parameter for the next requested slot. I have noticed that this is quite accurate (to the micro) and wanted to know if...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi All.
I made my PCB with nRF51822 and achieved around 150 Feet range (LoS). My target is to calculate a approximate distance (in Feet) from RSSI values.
I did a field...
I want to set up the HRS demo, but in reverse. I want to use my PCA10001 board to receive heart rate data from a peripheral device (already working and tested on my PC). It...
Hi,
i have a problem in my Code, when ic look nrf_delay_us (1000) on the oscilloscope i can se a puls withe 1,3 us thats not accurate enough. What could be a reason for...
Hi,
I have created Eclipse project to compile nRF51 DFU loader. This is a pure Eclipse project, no makfile. It has compile configurations for combination of Single/Dual...
Hi,
I am looking to build a beaon product based on nRF51822. There are several kits available shown below. Which kit should I pick to start the hardware design and firmware...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello,
I am using nrf51822 evaluation kit with ble_lbs (Led button sample) profile, I need the USB dongle source code for ble_lbs (Led button sample) profile because I...
Hi,
Is it possible to change the advertisement parameters of a beacon device without connecting to it?
(ex: major,minor value & interval)
Is it OK if our beacon product...
I use ble_app_uart demo of pca1001 and my SDK version is 5.2.0. I want to use APP_BUTTON_INIT to handle a button event. So I changed the buttons_init(void) like this:
static...
Hi, is it possible to add for example a
www.ti.com/.../technicaldocuments
On the nrf51822?
I would have to modify the S110 source to turn on and off the LNA and PA when...
Hi
I have created local buffer of 100 bytes.
while device is connected to dongle it is sending all 100 bytes over bluetooth stack .
but once it is disconnected and...
Hi everyone, I don't have the nRF51822 yet, but still want to get familiar with it as much as possible before I get to buy it. I was looking for a description of the functions...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
