I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hello all,
I am getting an error "No Memory for operation" while initializing connection parameters for nrf51822 application. Can somebody please advice me about this error...
Hi
Recently I attempted to modify the bootloader.When download the official bootloader, it could modify the value of (NRF_UICR_BASE+0x14).But if I Remove some code，when...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I'm building the ble_hrs_app for my pca10000, I've made a couple of changes (to change the LEDS which show) and I'm building it with CrossWorks .. which I thought I knew how...
Hello, I'm trying to get my nrf51822 project from SDK 5.0.0 running in the latest SDK 5.2.0. To minimize problems with KEIL I used the template project and copied my sources...
Hello,
I have a nRF51822 Evaluation Kit, and a working ble_app_uart demo software.
I would like use the Fujitsu MBH7BLZ02-109004 module . I can flash and verify the softdevice...
I am using the following code to manage a buffer to put through data to the ble stack. I think I saw a similar code on the nRFready Desktop 2 v1.0.4 examples:
/**@brief...
Are there any pin restrictions for connecting the PWM module to? That is, would I be able to output the a PWM signal (created by the internal PWM facility) through any P0...
Hello Gentlemen,
I'm developing an Android App that needs to connect to nRF. The nRF sensor does not have keyboard, display or buttom.
But we can have OOB which is a...
Hello!
I have two question from Heart Rate Application.
What BLE_L2CAP_MTU_DEF number presents?
I do not see event handlers for WAKEUP_BUTTON and BONDMNGR_DELETE_BUTTON...
Development Board can not be loaded by Keil 4.7.2
nRF51 by Nordic can not be identified by Keil automatically, how to configure the parameter for programming?
The Android API Kitkat documentation says the following about BluetoothSockect.connect()
"This method will block until a connection is made or the connection fails. If...
Hello Gentlemen,
I'm looking for sample code that shows how to enable security which prompts for a PIN number on the Android device when I want to connect to the nRF. ...
