Hi
I noticed one ticket says that "the following combination offers low power consumtion and high througput when needed :Short Connection Interval + High Slave Latency ...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
Hello,
I am new to Nordic platform, previously i had worked on TI controller.
I have three questions to ask:
1) My firmware consists of four services, each service...
hi,
I am using nRF52832 with KEIL. I want to use version6.0.0 softdevice, but I can't select from KEIL runtime library.
Also, the version that can be downloaded from...
I am trying to change after 10 seconds into non-connectable mode. I am using the below code for initializing:
I want to change mode into non-connectable using this type...
When I use dfu_nrf52832_xxAA_s132_6.1.1.hex, it works all devices updated with blink code as described in dfu_quick_start.md But without any provisioning Process, why? And...
Firstly , I have 2 phone. Phone A is huwawei using android 7 and Phone B xiaomi pocophone using android 9.
Phone A already success connect using UART. But I want to try...
I have a same question:
https://devzone.nordicsemi.com/f/nordic-q-a/22025/in-nrf52840-not-able-to-program-boot-loader-hex-is-using-nrfgo-studio/86420#86420
But I not working...
Hi, I am trying to run the following demo here: https://github.com/NordicPlayground/nRF52-ble-long-range-demo
I have followed the instructions and copied the demo folders...
In my understanding, only Nordic NRF Connect (Android and iOS) can be used to bootload a device using the Nordic DFU.
Is there a corresponding command line tool to perform...
I followed the issues from https://devzone.nordicsemi.com/f/nordic-q-a/54149/error-by-loading-solution-on-ses, which fixed the zephyr script issues, but was seeing the same...
Hi,
I have migrate to SDK14.2 the MPU9250 exemple from the peripheral folder in the nrf52-pesky exemples : https://github.com/e27182/nRF52832_pesky https://github.com/e27182...
I am using the nRF52840 DK with the s140 softdevice and am trying to copy the interrupt vector table to RAM to modify interrupts during run time.
I run the following function...
I am porting the eMD-6.12 firmware/library by Invensense for the part MPU9250 into the nRF52832. My toolchain is compiling through gcc allowing examples from SDK's to be quickly...
Hi,
We 're currently using an ARM SOM that will run Yocto Linux from NPX for our current project. We have the nrf52840 connect to this SOM via USB, and we want to be able...
I am using SDK V15 with an nRF52DK and Keil compiler.
I have difficulty finding an example to use a GPIO to drive a Piezo Buzzer. The requirement is very simple: use a GPIO...
