I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Hi, I'm a novice in embedded systems. I have board based on nrf52811 and firmware written for my device but when I received my board from production I could not load firmware...
Hi all,
I'm modifying the Matter Light Bulb example from Nordic's nRF Connect SDK to integrate I2S audio output on the nRF5340 DK. The goal is to play a continuous beep...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
I have been trying to use the Nordic security backend with the MQTT library (TLS transport). However, after I finally got everything to build , I am now getting runtime errors...
I am using 2 nRF528400DK boards. Each board has a unique BLE Mesh sample loaded. The samples were made by modifying the default mesh sample provided by zephyr. One sample...
Hi support
I am developing code for the application core on the nrf5340 and testing this on an nrf7002dk dev kit. I am using sdk version 3.0.0. The code needs to read from...
Hi, How I can use/install nRF Util software ( device, nrf5sdk-tools, etc ) in a lab without internet access on MacOS machine ? I can download ' nRF Command Line Tools' but...
hello everyone ...I am working on a project that uses the nRF52840 IC. I would like to implement a power-down mode to reduce power consumption. In my project, I am using BLE...
HI Teams
I found in the datasheet that the UART, I2C, and SPI on the nRF5340 share the same set of IDs. Does this mean that these three buses cannot be used simultaneously...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hi,
I am currently evaluating the Channel Sounding functionality for indoor localization. I would like to check how much Energy my Initiator and Reflector consume for...
Hello, I am currently developing on a custom board based on the nRF7002 + nRF5340. The SDK version is v2.8.0, and the development is based on the BLE Provisioning example...
Hello ,
I've been trying to build the wifi shell example sample for my nrf52840dk with a nrf7002ek shield. I'm setting the shield via CMakeLIsts ( set ( SHIELD nrf7002ek...
