I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
I'm trying to sample the 4 of the analog inputs on the nrf51822 at upwards of 10kHz and get the data out some how. Currently I'm using printf statements but that starts to...
I am porting my code (previously on 51822/SDK V12) to 52/SDK V14.
I have RTT logging working well on 51/SDK v12. In SDK V14 I noticed that the log module now is in experimental_log...
nRF52832
SDK14.0
Hi, how can I protect the bootloader from being overwritten? Ideally, I would never be updating the bootloader so it will be a permanent part of the device...
Hi
How stable is the RTT module and how trustworthy is it?
It is marked as unstable and I do not get any messages from the modules.
I use:
#define NRF_LOG_BACKEND_RTT_ENABLED...
Hi,
i would like to implement a very low power counter and used the template from this post . I've modified the example and used TIMER2 in counter mode triggered by LPCOMP...
Hi,
I'm trying to create a local network between an nrf51-DK and a mobile phone, android or iOS. The main goal is to be able to get TCP/IP connection between the nrf5x...
I am writing firmware for a BLE Nano device using the Nordic SDK 8.1. I was having problems where my device would suddenly stop printing to UART and stop trying to bond with...
I'm trying to set up a ble mesh with 3 servers and 1 client on an nrf52 PCA10040 dev kit. Upon debugging, I'm getting an error that says: '64, APP_ERROR: C:\Users\sesa463145...
I am using a NRF52-based platform and have BLE code based on the ble_app_hrs_c Hear rate monitor system.
Having set up for scan, I see many device (we have a lot of beacons...
After migrating from sdk 13 with buttonless dfu based app I meet follow error:
my app get FATAL error after exactly 3min. I guess it something related with power down mode...
I have a 3 channel setup on my SAADC module, which I sample according to a LFCLK timer. I notice after the first called to nrf_drv_saadc_sample() and receipt of the ADC results...
hi,everyone!
we use the example
"nRF5_SDK_14.0.0_3bcc1f7\examples\ble_peripheral\ble_app_uart\pca10040\s132"ble_app_uart,
we also defined
"#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
At the very end of this post from Nordic Info center I am doing the exact example at the very end.
infocenter.nordicsemi.com/index.jsp
This is the start to do a transmit...
Hello
I'm trying to track lost packets in a connection by showing the sequence number of each packet received. Specifically it's about an application that sends new measurements...
