Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi everybody,
I was looking for a better way to update a data, like a 32-bit-word, without the need to erase the entire page. Part of this question is already been asked...
I was going through all the supported SDKs for the nrf52840 and in all of them, it is mentioned that the ESB and FreeRTOS support is not there yet. Could someone please let...
Hello, I'm trying to implement a buttonless DFU via ANT for a custom nRF52 board. I've got the 212 v4.02 Softdevice and I'm using the 14.0.0 SDK. I am able to transmit and...
Dear
i want to nrf52832 to collect accelaration sensor data(SPI communication 8MHZ).
The sensor output datas per 250us,nrf52832 will lost the sensor interupt when 52832...
Good evening. I write a project on nrf51822 in which there are a number of services with a set of characteristics (write and read). I need to limit access to some characteristics...
Hello, I am working through the tutorials to understand how to better use the SDK. I am currently on the Advertising tutorial and have gotten a strange error that doesn't...
I'm developing an accurate and low drift millisecond-resolution timer on the NRF52. I'm limited to the resources on the NRF52 itself. Details of the system:
Initialise...
Is there anything special required to make a n52832 work the very first time the chip is programmed? Fuses to set, etc?
I'm new to nordic chips and I was handed a board...
While creating a DFU bootloader based on the bootloader_secure_ble example, I was having trouble getting a device to boot into DFU mode.
Initially the device would get...
(Sorry for the formatting. I don't know what's going on with it--the preview looks ok!)
I'm creating an application that uses
a modified version of the ble_nus
example...
Hello guys,
I have problem, I activate the BLE and connect it to my tablet application until then nothing wrong happens. But when I use sd_ble_gap_disconnect() to disconnect...
I plugged my nRF52 evaluation board to PC using a micro USB cable, dragged a ble_peripheral hex file from Nordic examples to the mounted JLINK drive, started up nRF Connect...
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12....
In nrf51422, what is the behavior of these registers when an external rail-to-rail clock source is applied?
Do I have to issue HFCLKSTART? If
not needed, does issuing...