Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I have used Arduino for some time and i am very new to NRF. So i am struggling with any thing i do. But i am really motivated to learn it.
Completed setup for eclipse to...
Hi, I am designing a PCB which consists of an analog circuitry (microphone + analog front end) and the nrf52832 chip. I am using inbuilt-ADC of this chip to sample the acoustic...
I use this demo [nRF51_SDK_10.0.0_HID_DFU_090216.rar] (/attachment/27e0b68cff3ffe4959299fcae336e844)
change rep_map_data[] add mouse and Consumer,but restart is no work ...
Hi,
(I'm a computer scientist, please be kind)
In the below attached image, I have collected the data outdoors (so no signal reflection or signal fading) from a single...
Hello all,
I am using nRF51822 BLE SDK 9.00 PCA10028. I want to configure the gpio pins as input to sense the voltage as high or low. how to configure it please suggest...
hi
i'm developing to nrf52832, sdk14.0 version.
for example, ble_app_uart project..
NRF_LOG_INFO("UART Start!");
printf("UART Start!");
-> In serial program,...
I have an application that do SW download to STM32L151 processor using NordicDongle with MasterEmulator.dll (Version 2.1.13.14)
It works good on my desktop windows 10 computer...
Hello,
we are trying to test the mesh functionality with nrf development kit. We erased the flash on the dev kit and we programmed it with softdevice version s132v3.0.0....
As stated in the topic. We use BLE to simulate UART. As for now, we have defined our own UUIDs but there would be more straight forward to use the well defined and used one...
Hi,
I have known your board support jlink ob；I want to debug through it ;
I want to know if i need to buy the software-license from SEGGER ？
and if i need buy the software...
Now facing the problem "After disconnected, the electric current increases"...
I think softdevice is working hard even after disconnected when connecting once.
Could you...
Hi,
I'm trying to write unit tests and have arrived at the point to write tests for ble characteristic addition to a service.
To offer some background, I have written...
Hello,
I use NRF51822 and I try to output UART message onto hyperterminal program.
but every message I send it contains "APP:INFO:" in front of the message.
like...
