Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I2s subcontract transmission, the sound is normal during the transmission of each packet, and there is noise when preparing next_buf. How to eliminate the noise? Looking forward...
Hello Community,
I want to request a timeslot with sd_radio_session_open(). Whenever i call this API function, the Application crashes with a HardFault.
I have no idea...
Hi Devzone!
I'm using 'nRF52840' as an edge device, and this device is going to continuously check the surrounding environment and send the value to mqtt broker of aws through...
Hi,
We are using nRF52832 with a custom protocol communication (not BLE, not Nordic). The communication is simple, one device is sending message and the other is receiving...
Once again I'm turning to this forum for help, as I'm stuck with an unusual issue. We have a custom board, which is supplied from one CR2032 battery and can also be suplied...
Hello,
I am having an odd issue when loading an app that uses FDS with softdevice, if I load the app without a bootloader the FDS library seems to work just fine but if...
on connection, the modem gets reset after ~ 1 minute from activation:
log:
[00:00:00.421,386] <dbg> nrf_cloud_transport.nct_topics_populate: shadow_get_topic: $aws/things...
I would like to implement functionality to use a digital temperature sensor TSYS01. I cannot find that this already is implemented in Zephyr so im wondering how i in best...
Hi there,
I want to use a LiFePO4 Cell to supply the nRF9160:
Is the MAX17224 suitable to power the nRF9160?
Is this Power "Sequence" OK? Productspecification nRF9160...
currently we are facing an issue with our testing that, our product battery is getting drained to 0 volts. we understand that we need to put a cutoff voltage from the firmware...
Hey folks,
I'm developing a long-range application with nRF52840 DK that (optionally) uses NUS (Nordic UART Service) to send data to Samsung S10+; there is no problem establishing...
Hello,
SDK 15.3.0
nRF52840-DK
s140
IDE:SES
I am running into an issue using the app timer and LPComp together. The error is NRF_FAULT_ID_SDK_ERROR, With RTT output...
Let say during the normal program flow I want to change often the edge direction which will trigger the event: rising edge, none, falling edge, none … Can I work direct with...
hi:
i want to know CKCON config is CKCON =0x01 or CKCON =0x02? because datasheet is CKCON =0x01
External data memory stretch control. 001: One stretch cycle (default)...
