Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
hello,
I am trying to integrating ble_nus_init( ), inside ble_beacon_app, receiving through NUS_service and transmitting through beacon,
but program is stuck inside ble_advertising...
Is it possible to assign connection handles non-sequentially, for example based on the device's Bluetooth name? For the solution I'm developing I'd like for a given sensor...
Hi,
I am getting lots of transmission errors using the Serial library. I changed the Serial_Uartes example by removing the serial1 interface and creating a simple loopback...
Hi all,
I am using nRF52832 DK to do some tests about power consumption. And I am facing a problem that every time I pressed the button and kept it down, the current would...
Checked out v1.0.0
This error seems to be unavoidable to me. I have deleted the git cache and even tried the --no-cache-dir option to pip3, but nothing seems to work.
...
Is there any documentation available explaining how to access the LTE modem without using the SDK ? Kinda limited information regarding the IPC peripheral and how to use it...
Hi,
We are developing a bluetooth scanner with our custom application on nrf52840 based custom board. We have external oscillator on our board. When I try to call the sd_softdevice_enable...
Hi All,
I am trying to build ANT examples for nrf52832 and i am getting below error.
PATH : nRF5_SDK_16.0.0_98a08e2\examples\ant\ant_advanced_burst\pca10040\s212\ses...
Hello,
The datasheet shows example circuit configurations with C3=C4=1pF and L1=3.9nH. But the downloaded reference design shows C3=0.8pF, C4=0.5pF, L1=4.7nH, plus an empty...
I try to incorporate the usb dfu trigger into my application. However when using nrf Connect for Desktop to flash the nrf52840 dongle it can not reopen the dongle.
This...
I'm using SDK 15.3 and Mesh 3.20 on a system, that works fine with LPN and nodes with friend-features. The LPN can initiates (establish) friend connection, request status...
Hi !
In order to consume lowest current，we use the function power_manage() ，let the MCU go into sleep，the SD is S130, V1.0，we enable the GPIOTE，watchdog ，ADC ，app_timer...
Hai, I'm trying to learn the UART using the example code available in nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_uart. I'm using BMD-300 Evaluation Board. I'm...
I am looking at the NRF52832 for some projects and so downloaded the SDK and opened an example project in Segger Embedded Studio (SES). I was shocked to find that the directory...
