after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi. I don't understand how to build nrf_drv_saadc.c with gcc. I'm getting this error in the EVT_TO_STR() macro:
Compiling file: nrf_drv_saadc.c
In file included from ...
Hello,
I'm going to use nrf52-ble-image-transfer-demo-master for my application.
But demo used other way with cpp code for configuring nrf52832 interfaces(spi, twi, gpio...
Hello Folks,
Nice to see an active developer community out here! I ran into some issues last night which I hope could be resolved. We procured nRF52840 SoCs and have developed...
Hi all,
i'm new to BLE in general, I found this chip (nrf52832), which suits my uni project.
However, I don't have much knowledge about this technology. therefore, im...
Hi everyone,
I would like to test the capabilities of nRF52840. I understand that it should be capable of higher throughput (x2), increased broadcast capacity (x8), and...
Hi,
I need solution for modbus interface.
My One Central connected with Modbus Server App and 8 slave connected with each peripheral.
which SDK and Mode used for this...
Hi,
I just read Understanding NRF_ERROR_BUSY and wanted to know if this is true for the S132 V5 softdevice.
So each connection can queue one system Tx packet and one...
Hi everyone !
We migrated a functional code from IAR to GCC compiler. But we got some trouble working it with GCC. The code compiles but it doesn't act properly with GCC...
I have used Arduino for some time and i am very new to NRF. So i am struggling with any thing i do. But i am really motivated to learn it.
Completed setup for eclipse to...
Hi, I am designing a PCB which consists of an analog circuitry (microphone + analog front end) and the nrf52832 chip. I am using inbuilt-ADC of this chip to sample the acoustic...
I use this demo [nRF51_SDK_10.0.0_HID_DFU_090216.rar] (/attachment/27e0b68cff3ffe4959299fcae336e844)
change rep_map_data[] add mouse and Consumer,but restart is no work ...
Hi,
(I'm a computer scientist, please be kind)
In the below attached image, I have collected the data outdoors (so no signal reflection or signal fading) from a single...
Hello all,
I am using nRF51822 BLE SDK 9.00 PCA10028. I want to configure the gpio pins as input to sense the voltage as high or low. how to configure it please suggest...
