after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
hey, i am strating with nrf52840 for thread.
i want to know if there is a need to add an antenna to the SoC? if not i can't visualize where is the antenna in the nrf52 DK...
Hi Nordic Team,
In my BLE project, the peripheral device has the ability to do both scanning and advertising. So please suggest a way of how the central device would know...
Hi all,
I have bought the NRF51822 evaluation kit ( NRF51822 ). I have some question about this.
1) Is it necessary to program the device?
2) what is the nominal operation...
SDK15.3
SES
nRF52840
Hello Folks,
I'm trying to reduce my applications power consumption further in system off mode. For testing my IO configuration and System...
I am trying to build one of the Thread examples.
nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b\examples\thread\simple_coap_client\pca10056
Keil uVusion V5.15
When...
Hi everyone,
my problem is pretty simple: we developed a custom board for the NRF52840 to work using a custom protocol or BLE. A few sensors are connected to the NRF using...
Hi,
I am using NCS v1.1.0 and modem fw 1.1.0.
We had prepared our application in NCS v1.0.0 and now i have moved it to v1.1.0.
In new sdk v1.1.0 ,When i try to get Address...
Hello , I am advertising from a nrf device with advertising interval of 40ms. and I want to measure this interval at scanning side.
How I can measure using timer , timer...
I am using nRF52 DK to evaluate the TX power settings using sd_ble_gap_tx_power_set command:
sd_ble_gap_tx_power_set ( BLE_GAP_TX_POWER_ROLE_CONN , m_conn_handle, tx_power...
I have a project that needs to scan and filter the advertising name, uuid and mac address from the device. I will set them one by one and enable them one by one. I set them...
My problem seems to be a lot like case numbers 217967 and 243215.
I do not have an oscilloscope or logic analyzer.
I am using a nRF52840 DK (PCA10056 1.0.0 2018-17) and...
I've just received my nRF9160 development kit this morning and after trying to setup the development environment for a few hours I've come to a halt.
I got it working...
I am looking to use libuarte in our project. We are creating a battery powered device and so need to be low powered. EasyDMA draws about 1mA when running which is far too...
