after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am able to flash/program nrf51822 with openOCD on Raspberry-pi and STLink-v2
but when I invoke Open On-Chip Debugger on telnet to write on UICR register, it don't give...
Hi everyone,
I am currently working on a project that leads me to save a respectful amount of data.
Some of the objects that I save size a few KB actually.
I would...
Estimate battery life for FOB CR 2032 -240 mAh
We are developing remote with CR2032 battery and using Nordic nrf51-1822 BLE, 960 m sec connection interval, RX 1 packet...
I want to use nRF52840 Device to implement non-connectable advertisement and scan on one board.
To be more specific, I want to advertise information for some time period...
I am using NRF52 SDK14.0 and SoftDevice S132 v5.0.0. Application freezes somewhere in SoftDevice if sd_softdevice_enable() is called after nrf_drv_clock_lfclk_request() was...
Hello All,
Where would I find a library file for a PID controller? Forgive me if there is an obvious answer. I'm new to working with Keil.
Thanks for taking the time...
We need to put the processor in sleep mode (to conserve battery power) and wake-up the processor when the user touches the Cap Sensor pad.
Can you Cap Sensor in nrf52 be...
I'm using "nrf5_SDK_for_Mesh_v0.9.2-Alpha". And, I build examples using "SEGGER Embedded Studio 3.26a".
Now I want to modify examples for my custom board.
In CMake, "...
Hi, a little background information first, when debugging ble mesh example 0.9.x:
devzone.nordicsemi.com/.../
I'm now kinda having a massive problem with this function...
Hi,all.
I am using nRF52832.
Does the nRF52832 support dual mode that allows simultaneous advertising and scanning?
Are there any examples you can refer to if you...
Hi I use SDK 12.3 and sdk 2.0.1 , and set a device name length is 21 like "1234567890ABCDEFGHIJK" by sd_ble_gap_device_name_set;
but in the advertise data the name length...
Hi,
we are developing and application on iOS which can among others, update our hardware over the air, and we found out that e.g. after bootloader update is done, then...
Our hardware has an externa memory connected to the nRF51 by SPI, we also use DFU to update the firmware creating the zip pack (We have buttonless dfu working as well) and...
I've been using the nRF52832 chip for over a year and it works great. However, for a new project I designed a board so that the nRF52 chip was the slave on a SPI bus, and...
