I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hello,
I'm encountering a very strange problem while attempting to run an fstorage fs_erase operation on my peripheral device when the central is connected. This is on...
Hello,
I want to make a device that use a Zigbee SoC and a nRF51822 for BLE, and I want to make it in the same board, that imply to have two antennas in the board.
I...
Hello,
This is Milav Form Teq Diligent,India.
I read the Bluetooth core 4.0 pdf.
In that they defined the " Park State " .
is this state are available in nRF51822...
Are any of the freeRTOS examples Power Optimized? I've looked into other related posts but not sure anyone is seeing the same issues I'm seeing. I'm using a Rigado BMD300...
Hello: I'm about to test out the ble mesh dfu, and to do that I need to flash my device, which is nrf52840, with precomped bootloaders.
Now here is the problem: Which one...
We need to certificate our ble devices. I use DTM example. Already I connected to device and flash example. Which correct command can I send from PuTTY console for check that...
I have trouble making iOS to reconnect after a device firmware update: I assume the issue
is due to flash being rewritten and so loosing information about the iOS peer.
...
I'm wanting to design a mesh system that will be running on batteries.
I need to keep track of the battery voltage. I don't plan on monitoring it often maybe a few times...
Hi All,
I am trying to interface an SPI OLED display 128x32 with my nrf51422 development kit over SDK 12.2.0 with BLE. After the program gets compiled, i am getting this...
I am designing a board with a host cpu and Nordic nRF52832 as companion chip in order to have Bluetooth capabilities; the two SoCs are connected each other through the uart...
Hello,
I've been trying to program my nrf52832 board with an st link v2 dongle or an st32 disco board with no luck with eclipse(Didn't find a dedicated tut for using all...
Hello
i am using the nrf52840 with sdk 13.
on the client side i saw you are catching the cccd_handle. for the heart rate characteristic.
basically i am leaning the basic...
Hi all, is it possible to use NRF51-DK for Master Control Panel?
I dont have NRF51 dongle so I was thinking if there is a way to make NRF51-DK work with MCP.
Hi,
I have the following situation:
1 central connects and bonds to 2 peripherals. All the above 3 devices are power cycled.
Now, the central need to remember the...
My system's data rate is 16MHz.it input to nRF52832 is parallel 8 bits. Is it possible? I want input the data to RAM by easyDMA,please to tell me how to do it ? thanks!
